标准规范中文版翻译 Archivers

标准规范中文版翻译 » Archivers » SAE 标准数据库参考目录 3

SAE AMS 4216B-2003 固溶热处理的和人工老化的含1.0Mg-0.8Si-0.8Cu-0.50Mn(6013-T6)铝合金薄板 5 页
SAE AMS 4217G-1996 固溶热和脱溶热处理的含7.0Si-0.32Mg(356.0-T6)铝合金铸件 9 页
SAE AMS 4218H-2001(R2006) 固溶热和脱溶热处理的含7.0Si-0.35Mg(A356.0-T6P)(原来T61P回火)铝合金铸件 页
SAE AMS 4219E-2001 固溶热和脱溶热处理的含7.0Si-0.55Mg-0.12Ti-0.06Be(A357.0 T61P)铝合金铸件 9 页
SAE AMS 4221B-2005 Aluminum Alloy, Plate 4.4Cu - 1.5Mg - 0.60Mn (2124-T8151) Solution Heat Treated, Stress Relieved, and Precipitation Heat Treated UNS A92124 页
SAE AMS 4223C-1996 固溶热处理的和时效处理的含4.5Cu-0.70Ag-0.30Mn-0.25Mg-0.25Ti(A201.0-T4)铝合金铸件 10 页
SAE AMS 4224B-1987(R2000) 稳定处理的含4.0Cu-2.1Ni-2.0Mg-0.30Cr-0.30Mn-0.13T-0.13V(243.0)砂型铝合金铸件 9 页
SAE AMS 4225C-1996 固溶热处理的和稳定处理的含5.0Cu-1.5Ni-0.25Mn-0.25Sb-0.25Co-0.20Ti-0.20Zr(203.0-T7)铝合金耐热铸件 11 页
SAE AMS 4229D-2001(R2006) 固溶热处理的和过老化的含4.5Cu-0.70Ag-0.30Mn-0.25Mg-0.25Ti(A201.0-T7)高强度铝合金铸件 页
SAE AMS 4232A-2001(R2006) 固溶热处理的、冷处理的和脱溶热处理的含2.7Cu-2.2Li-0.12Zr(2090-T86)铝合金挤压件 页
SAE AMS 4233C-2003 含4.5Cu-0.70Ag-0.30Mn-0.25Mg-0.25Ti(201)铝合金焊丝 6 页
SAE AMS 4235A-1987(R2000) 固溶热和脱溶热处理的含4.6Cu-0.35Mn-0.25Mg-0.22Ti(A206.0-T71)铝合金铸件 10 页
SAE AMS 4236A-1987(R2000) 固溶热处理的和时效处理的含4.6Cu-0.35Mn-0.25Mg-0.22Ti(A206.0-T4)铝合金铸件 10 页
SAE AMS 4237A-1987(R2000) 固溶热处理的和时效处理的含4.6Cu-0.35Mn-0.25Mg-0.22Ti(206.0-T71)砂型铝合金铸件 9 页
SAE AMS 4241C-2002 固溶热和脱溶热处理的、晶枝间距被控制的含7.0Si-0.58Mg-0.15Ti-0.06Be(D357.0-T6)铝合金铸件 11 页
SAE AMS 4242A-1997 固溶热处理的和过老化的含4.7Cu-0.60Ag-0.35Mn-0.25Mg-0.25Ti(B201.0-T7)铝合金铸件 11 页
SAE AMS 4243B-2003 固溶热处理的和过老化的含6.2Zn-2.3Cu-2.2Mg-0.12Zr(镀铝的7050-T76)镀铝的铝合金薄板 6 页
SAE AMS 4244A-2001(R2006) 焊接A206.0型合金用含4.6Cu-0.35Mn-0.25Mg-0.22铝合金焊丝 页
SAE AMS 4245C-2003 含5.0Si-1.2Cu-0.50Mg(355)铝合金焊丝 6 页
SAE AMS 4246C-2003 含7.0Si-0.52Mg(357)铝合金焊丝 6 页
SAE AMS 4247B-1994 Aluminum Alloy, Hand Forgings 7.7Zn - 2.4Mg - 1.6Cu - 0.16Cr (7049- T7352) Solution Heat Treated, Stress Relieved by Compression, and Precipitation Heat Treated UNS A97049 页
SAE AMS 4248A-1993(R2000) 固溶热处理的、加压消除应力的和脱溶热处理的含1.0Mg-0.60Si-0.28Cu-0.20Cr(6061-T652)铝合金手工锻件和轧制环件 7 页
SAE AMS 4248B-2006 Aluminum Alloy Hand Forgings and Rolled Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T652) Solution Heat Treated, Stress Relief Compressed, and Precipitation Heat Treated UNS A96061 页
SAE AMS 4249A-2005 固溶热和脱溶热处理的含7.0Si-0.58Mg-0.15Ti-0.06Be(D357.0-T6)铝合金铸件（要求疲劳和断裂韧度测试） 13 页
SAE AMS 4250A-2005 固溶热处理、消除应力和过老化的含8.1Zn-2.3Mg-1.0Cu-Zr(7449-T7651)铝合金板材 页
SAE AMS 4251-2006 固溶热处理的、冷处理的和脱溶热处理的含2.7Cu-2.2Li-0.12Zr(2090-T83)铝合金薄板 页
SAE AMS 4252B-2005 固溶热处理、消除应力和过老化的含6.4Zn-2.4Mg-2.2Cu-0.12Zr(7150-T7751)铝合金板材 7 页
SAE AMS 4254A-1993(R2000) 含4.4Cu-1.5Mg-0.6Mn(2024-T3)芳族聚酰胺纤维增强的3,5,7,或9层铝合金层压薄板 7 页
SAE AMS 4255B-2005 加工状态的含0.6Mg - 0.35Si - 0.28Cu（No.21钎焊薄板）的单面涂层铝合金薄板 6 页
SAE AMS 4256B-2005 加工状态的含0.6Mg - 0.35Si - 0.28Cu（No.22钎焊薄板）的双面涂层铝合金薄板 6 页
SAE AMS 4258-1992(R2000) 含5.7Zn-2.2Mg-1.6Cu-0.22Cr(单面镀铝7475-T761)芳族聚酰胺纤维增强的5或7层铝合金层压薄板 7 页
SAE AMS 4260F-2001(R2006) 固溶热和脱溶热处理的含7.0Si-0.32Mg(356.0-T6)铝合金熔模铸件 页
SAE AMS 4261E-1998(R2006) 脱溶热处理的含7.0Si-0.32Mg(356.0-T51)铝合金熔模铸件 页
SAE AMS 4267-2005 退火的含8.0Zn-2.3Cu-2.0Mg-0.16Zr(7055-O)铝合金薄板 6 页
SAE AMS 4270A-1997 固溶热处理的和冷处理的含4.1Cu-1.4Mg-0.45Mn(镀铝的2424-T3)镀铝的铝合金平薄板 7 页
SAE AMS 4273B-2006 Aluminum Alloy, Sheet and Plate (2424-T3 Flat Sheet and Plate) Solution Heat Treated and Cold Worked UNS A92424 页
SAE AMS 4274-1997 细晶粒、退火的含4.4Cu-1.5Mg-0.60Mn(镀铝的2024-0)镀铝的铝合金薄板 7 页
SAE AMS 4276A-2005 Aluminum Alloy, Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-0) Annealed, Fine Grained UNS A92024 页
SAE AMS 4277A-2005 Aluminum Alloy, Sheet 5.6Zn - 2.5Mg - 1.6Cu - 0.23Cr (7075-0) Annealed, Fine Grained UNS A97075 页
SAE AMS 4278B-2003 细晶粒的、退火的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(镀铝的7075-0)镀铝的铝合金薄板 7 页
SAE AMS 4279B-2006 Aluminum Alloy, Alclad Sheet 4.4Cu - 1.5Mg - 0.60Mn (2024-T4 Flat Sheet) Solution Heat Treated, High Formability UNS A82024 页
SAE AMS 4280H-2001(R2006) 固溶热处理的和过老化的含5.0Si-1.2Cu-0.5Mg(355.0-T71)铝合金金属型铸件 页
SAE AMS 4281F-2001(R2006) 固溶热和脱溶热处理的含5.0Si-1.2Cu-0.50Mg(355.0-T6)铝合金金属型铸件 页
SAE AMS 4284G-2001(R2006) 固溶热和脱溶热处理的含7.0Si-0.30Mg(356.0-T6)铝合金金属型铸件 页
SAE AMS 4285C-2001(R2006) 固溶热和脱溶热处理的含7.0Si-0.30Mg(356.0-T6)铝合金离心铸件 页
SAE AMS 4286E-2001(R2006) 脱溶热处理的含7.0Si-0.32Mg(356.0-T51)铝合金金属型铸件 页
SAE AMS 4287-2006 Aluminum Alloy, Extrusion 2.7 Cu - 1.8 Li - 0.7 Zn - 0.3 Mn - 0.3 Mg - 0.08 Zr (2099-T83) Solution Heat Treated, Stress Relieved by Stretching 1% to 4% and Aged UNS A92099 页
SAE AMS 4288-2001 固溶热和脱溶热处理的含7.0Si-0.58Mg-0.15Ti(E357.0-T6)铝合金铸件 12 页
SAE AMS 4289-2001 固溶热处理的含7.0Si-0.55Mg-0.12Ti(E357.0-T6)铝合金铸件 11 页
SAE AMS 4290K-2005 Aluminum Alloy, Die Castings 9.5Si - 0.50Mg (360.0-F) As Cast UNS A03600 页
SAE AMS 4291G-2005 Aluminum Alloy, Die Castings 8.5Si - 3.5Cu (A380.0-F) As Cast UNS A13800 页
SAE AMS 4293-2003 固溶热处理的、消除应力的、矫直的和过老化的含7.9Zn-1.6Cu-2.2Mg-0.16Cr(7249-T76511)铝合金挤压件 6 页
SAE AMS 4294-2001(R2006) 挤压热处理的、拉伸消除应力的、矫直的和人工老化的含1.0Mg-0.60Si-0.28Cr(6061-T5511)铝合金挤压件 页
SAE AMS 4295B-2006 Aluminum Alloy, Sheet and Plate 6.3Cu - 0.30Mn - 0.06Ti - 0.10V - 0.18Zr (2219 - O, F, T31, T351, T37, T81, T851, T87) UNS A92219 页
SAE AMS 4296A-2003 固溶热处理的和冷处理的含4.3Cu-1.4Mg-0.60Mn(镀铝的2524-T3)镀铝的铝合金薄板和板材 7 页
SAE AMS 4297-1998 固溶热处理的、高成型性含4.4Cu-1.5Mg-0.60Mn(2024;-T4平薄板)铝合金薄板 5 页
SAE AMS 4298-2004 固溶热处理的和冷处理的含3.8Cu-1.0Mg-0.30Mn-0.60Zn(镀铝的2056-T3)镀铝的铝合金薄板 6 页
SAE AMS 4299-2005 固溶热处理、消除应力和过老化含8.1Zn-1.8Cu-2.3Mg的铝合金板材(7449-T7951) 6 页
SAE AMS 4300B-1990(R1994) 扩散粘结用含50 v/o 5.6B, 6061-0的硼-铝复合薄板 8 页
SAE AMS 4302A-1992(R2000) 含5.7Zn-2.2Mg-1.6Cu-0.22Cr(7475-T761)芳族聚酰胺纤维增强的3,5,7,或9层铝合金层压薄板 7 页
SAE AMS 4303A-2000 固溶热处理的、冷处理的和老化的含2.7Cu-2.2Li-0.12Zr(2090-T81)铝合金板材 6 页
SAE AMS 4304-1993(R2000) 固溶热处理的、拉伸的和脱溶热处理的含2009/SiC/15w(T8P)不连续增强的铝合金薄板 6 页
SAE AMS 4305-2005 Aluminum Alloy, Extruded Profiles (7449-T79511) 8.1Zn - 1.8Cu - 2.2Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged Composition similar to UNS A97449 页
SAE AMS 4306A-1993(R2000) 固溶热处理的、消除应力的和老化的含6.4Zn-2.4Mg-2.2Cu-0.12Zr(7150-T6151)铝合金板材 7 页
SAE AMS 4310D-2001(R2006) 固溶热处理的、机械消除应力的和脱溶热处理的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7075-T651,7075-T652)铝合金轧制或锻制的环件 页
SAE AMS 4311D-2003 固溶热处理的、机械消除应力的和脱溶热处理的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7075-T7351,7075-T7352)铝合金轧制或锻制的环件 7 页
SAE AMS 4312C-2000(R2006) Aluminum Alloy, Rolled or Forged Rings 1.0Mg - 0.60Si - 0.28Cu - 0.20Cr (6061-T651, 6061-T652) Solution Heat Treated, Mechanically Stress Relieved, and Precipitation Heat Treated UNS A96061 页
SAE AMS 4313C-2001(R2006) 固溶热处理的和机械消除应力的含6.3Cu-0.30Mn-0.18Zr-0.10V-0.06Ti(2219-T351,2219-T352)铝合金轧制或锻制的环件 页
SAE AMS 4314D-2005 固溶热处理、机械消除应力和脱溶热处理含4.5Cu-0.85Si-0.80Mn-0.50Mg(2014-T651,2014-T652)轧制或锻制的铝合金环件 8 页
SAE AMS 4315-2005 固溶热和脱溶热处理的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7075:-T76薄板,-T7651板材)的铝合金薄板和板材 页
SAE AMS 4316-2005 固溶热和脱溶热处理的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7075:-T76薄板,-T7651板材)镀铝的铝合金薄板和板材 页
SAE AMS 4317-2005 固溶热处理和过老化的7075-T76(51X)含5.6Zn-2.5Mg-1.6Cu-0.23Cr的铝合金挤压棒材、杆材和型材 页
SAE AMS 4319B-2003 固溶热处理的、消除应力的和人工老化的含12.2Si-1.0Mg-0.90Cu-0.90Ni(4032-T651)轧制的或冷加工的铝合金棒材和杆材 5 页
SAE AMS 4320B-2005 Aluminum Alloy Forgings 7.7Zn - 2.5Mg - 1.5Cu - 0.16Cr (7149-T73) Solution and Precipitation Heat Treated UNS A97149 页
SAE AMS 4321A-1993(R2000) 含7.7Zn-2.5Mg-1.5Cu-0.16Cr(7049-01)高温退火的铝合金锻件 12 页
SAE AMS 4323B-2003 固溶热处理的、消除应力的和脱溶热处理的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7075-T7452)铝合金手工锻件 7 页
SAE AMS 4324-2002 固溶热处理的、消除应力的和过老化的(7055-T74511)含8.0Zn-2.3Cu-2.0Mg-0.16Zr挤压的铝合金杆材、棒材和型材 7 页
SAE AMS 4325-2003 固溶热处理的、消除应力的、矫直的和过老化的(7150-T77511)含6.4Zn-2.4Mg-2.2Cu-0.12Zr挤压的铝合金宽板型材 7 页
SAE AMS 4326-2004 固溶热处理、拉伸消除应力和老化的含1.0Mg-0.80Si-1.8Cu-0.20Cr(2013-T6511)挤压的2013铝合金棒材、杆材和型材 6 页
SAE AMS 4327-2003 退火的(2098-O)含3.5Cu-1.1Li-0.50Mg-0.40Ag-0.11Zr铝合金板材 6 页
SAE AMS 4328-2003 固溶热处理的、冷处理的和人工老化的(2397-T87)含2.8Cu-1.4Li-0.30Mn-0.12Zr-0.10Zn铝合金板材 7 页
SAE AMS 4328A-2006 Aluminum Alloy, Plate (2397-T87) 2.8Cu - 1.4Li - 0.30Mn - 0.12Zr - 0.10Zn Solution Heat Treated, Cold Worked, and Artificially Aged UNS A92397 页
SAE AMS 4329A-2006 Aluminum Alloy, Plate (7085-T7651) 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr Solution Heat Treated, Stress-Relieved, and Overaged UNS A97085 页
SAE AMS 4330B-2004 固溶热处理、拉伸和人工老化的含2.8Cu-1.5Li-0.30Mn-0.12Zr(2297-T87)铝合金板材 8 页
SAE AMS 4331-2003 固溶热处理的、消除应力的和脱溶热处理的含7.8Zn-2.6Mg-2.0Cu-0.10Zr-(7068-T6511)铝合金挤压件 5 页
SAE AMS 4332-2005 固溶热处理、消除应力和过老化含8.1Zn-1.7Cu-2.2Mg-0.16Zr的铝合金挤压型材(7349-T76511) 6 页
SAE AMS 4333B-2005 Aluminum Alloy, Die Forgings 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged Composition similar to UNS A97050 页
SAE AMS 4335-2001(R2006) 铝合金2xxx和7xxx锻件热处理的、加工的部分的性能：快速横向拉伸性能和断裂韧度 页
SAE AMS 4336A-2003 固溶热处理的、消除应力的和过老化的(7055-T76511)含8.0Zn-2.3Cu-2.0Mg-0.16Zr挤压的铝合金杆材、棒材和型材 7 页
SAE AMS 4337-1998 固溶热处理的、消除应力的和过老化的(7055-T77511)含8.0Zn-2.3Cu-2.0Mg-0.16Zr挤压的铝合金型材 7 页
SAE AMS 4337A-2006 Aluminum Alloy, Extruded Profiles (7055-T77511) 8.0Zn - 2.3Cu - 2.0Mg - 0.16Zr Solution Heat Treated, Stress Relieved, and Overaged UNS A97055 页
SAE AMS 4338-2001 固溶热处理的和拉伸消除应力的(2026-T3511)含4.0Cu-1.3Mg-0.60Mn铝合金挤压件 7 页
SAE AMS 4339A-2004 固溶热处理的、冷处理的和人工老化的含4.4Cu-1.5Mg-0.60Mn(2024-T851)轧制的或冷精加工的铝合金棒材和杆材 5 页
SAE AMS 4340D-1998 固溶热处理的、消除应力的、矫直的和过老化的含6.2Zn-2.3Cu-2.2Mg-0.12Zr(7050-T76511)铝合金挤压件 8 页
SAE AMS 4340E-2006 Aluminum Alloy, Extrusions 6.2Zn - 2.3Cu - 2.2Mg - 0.12Zr (7050-T76511) Solution Heat Treated, Stress Relieved, Straightened, and Overaged UNS A97050 页
SAE AMS 4341D-1998 固溶热处理的、拉伸消除应力的、矫直的和过老化的含6.2Zn-2.3Cu-2.2Mg-0.12Zr(7050-T73511)铝合金挤压件 8 页
SAE AMS 4342D-2000 固溶热处理的、消除应力的、矫直的和过老化的含6.2Zn-2.3Cu-2.2Mg-0.12Zr(7050-T74511)铝合金挤压件 8 页
SAE AMS 4343D-2004 固溶热处理、拉伸消除应力和过老化的含7.7Zn-2.4Mg-1.6Cu-0.16Cr(7149-T73511)铝合金挤压件 6 页
SAE AMS 4344B-1998 固溶热处理的、拉伸消除应力的、矫直的和过老化的含5.6Zn-2.5Mg-1.6Cu-0.23Cr(7175-T73511)铝合金挤压件 7 页
SAE AMS 4345B-2005 固溶热处理、消除应力、矫直和过老化的含6.4Zn-2.4Mg-2.2Cu-0.12Zr(7150-T77511)铝合金挤压件 8 页
SAE AMS 4347B-2001 固溶热处理的和时效处理的含1.0Mg-0.8Si-0.8Cu-0.5Mn(6013-T4)铝合金薄板 5 页
SAE AMS 4348C-1995 350°F(177°C)，5052夹层结构用防腐蚀的铝合金蜂窝芯材 15 页
SAE AMS 4349C-1995 350°F(177°C)，5056夹层结构用防腐蚀的铝合金蜂窝芯材 15 页
SAE AMS 4350M-1998(R2006) 挤压状态的含6.5A1-0.95Zn(AZ61A-F)的镁合金挤压件 页
SAE AMS 4352H-1998(R2006) 脱溶热处理的含5.5Zn-0.45Zr(ZK60A-T5)的镁合金挤压件 页
SAE AMS 4362E-1992(R2000) 含5.5Zn-0.45Zr(ZK60A-T5)脱溶热处理的镁合金锻件 7 页
SAE AMS 4375K-2005 含3.0Al-1.0Zn-0.20Mn(AZ31B-0)退火的和重结晶的镁合金薄板和板材 页
SAE AMS 4376G-2005 含3.0Al-1.0Zn-0.20Mn(AZ31B-H26)冷轧和局部退火的镁合金板材 页
SAE AMS 4377H-2005 Magnesium Alloy, Sheet and Plate 3.0Al - 1.0Zn - 020Mn (AZ31B-H24) Cold Rolled, Partially Annealed UNS M11311 页
SAE AMS 4382D-2006 Magnesium Alloy, Plate, Extra Flat 3.0Al ?1.0Zn ?0.20Mn (AZ31B-0) Annealed UNS M11311 页
SAE AMS 4395E-2000(R2006) 含9.0Al-2.0Zn(AZ92A)镁合金焊丝 页
SAE AMS 4396D-2000 含3.3Ce-2.5Zn-0.72Zr(EZ33A)镁合金焊丝 6 页
SAE AMS 4401-2006 Aluminum Alloy Plate (7140-T7451) 6.6Zn - 1.8Cu - 2.0Mg - 0.10Zr Solution Heat Treated, Stress Relieved and Overaged 页
SAE AMS 4402-2006 Aluminum Alloy, Extruded Profiles (2024-T432) 4.4Cu - 1.5Mg - 0.6Mn Annealed, Stretch Formed, Solution Heat Treated and Stress Relieved by Stretching UNS A92027 页
SAE AMS 4403-2006 Aluminum Alloy, Die Forgings 7.5Zn - 1.6Cu - 1.5Mg - 0.12Zr (7085-T7452) Solution Heat Treated, Compression Stress-Relieved, and Overaged UNS A97085 页
SAE AMS 4404-2006 Aluminum Alloy, Extruded Profiles (6056-T4511) 1.0Si - 0.90Mg - 0.80Cu - 0.60Mn - 0.40Zn Solution Heat Treated and Stress-Relieved by Stretching UNS A96056 页
SAE AMS 4405-2006 Aluminum Alloy, Alclad Sheet (6156-T4) 1.0Si - 0.90Cu - 0.60Mn - 0.90Mg Solution Heat Treated and Naturally Aged 页
SAE AMS 4417A-2005 Castings, Sand, Magnesium Alloy 1.5Ag - 2.1Di - 0.08Cu - 0.70Zr (EQ21 - T6) Solution and Precipitation Heat Treated Composition similar UNS MI8330 页
SAE AMS 4418G-2004 固溶热和脱溶热处理的含2.5Ag-2.1Di-0.70Zr(QE22A-T6)的砂型镁合金铸件 9 页
SAE AMS 4420M-1992(R2000) 铸造状态的含6Al-3Zn(AZ63A-F)砂型镁合金铸件 9 页
SAE AMS 4426A-2003 固溶热和脱溶热处理的含5.1Y-3.0Re-0.70Zr(WE54-T6)砂型镁合金铸件 9 页
SAE AMS 4427A-2001 固溶热和脱溶热处理的含4.0Y-2.3Nd-0.7Zr(WE43B-T6)的砂型镁合金铸件 11 页
SAE AMS 4429-2004 固溶热和脱溶热处理的含2.8Nd-1.4Gd-0.4Zn-0.6Zr(EV31A-T6)的砂型镁合金铸件 9 页
SAE AMS 4434L-2005 固溶热和脱溶热处理的含9.0Al-2.0Zn(AZ92-T6)砂型镁合金铸件 页
SAE AMS 4437E-2003 固溶热处理的和老化的含8.7Al-0.70Zn(AZ91C-T6)的砂型镁合金铸件 8 页
SAE AMS 4439E-2001 脱溶热处理的含4.2Zn-1.2Ce-0.7Zr(ZE41A-T5)的镁合金铸件 9 页
SAE AMS 4442E-1993(R2000) 脱溶热处理的含3.2Ce-2.5Zn-0.70Zr(EZ33A-T5)砂型镁合金铸件 10 页
SAE AMS 4443F-2006 Magnesium Alloy, Sand Castings 4.5Zn - 0.75Zr (ZK51A-T5) Precipitation Heat Treated UNS M16510 页
SAE AMS 4444C-1992(R2000) 脱溶热处理的含6.0Zn-0.80Zr(ZK61A-T5)砂型镁合金铸件 9 页
SAE AMS 4446B-2006 Magnesium Alloy, Sand Castings 8.7Al - 0.70Zn - 0.26Mn (AZ91E-T6) Solution and Precipitation Heat Treated UNS M11919 页
SAE AMS 4452C-2006 Magnesium Alloy, Investment Castings 8.7Al - 0.70Zn - 0.22Mn (AZ91C-T6) Solution and Precipitation Heat Treated UNS M11914 页
SAE AMS 4453D-2006 Magnesium Alloy, Investment Castings 9.0Al - 2.0Zn (AZ92A-T6) Solution and Precipitation Heat Treated UNS M11920 页
SAE AMS 4455E-2006 Magnesium Alloy, Investment Castings 10Al (AM100A-T6) Solution and Precipitation Heat Treated UNS M10100 页
SAE AMS 4483C-1992(R2000) 固溶热和脱溶热处理的含10Al(AM100A-T6)金属型镁合金铸件 9 页
SAE AMS 4484J-1992(R2000) 固溶热和脱溶热处理的含9.0Al-2.0Zn(AZ92A-T6)金属型镁合金铸件 18 页
SAE AMS 4490H-2005 Magnesium Alloy Castings, Die 9.0Al - 0.70Zn (AZ91D, Temper F) As Cast Composition similar to UNS M11916 页
SAE AMS 4500H-2000 软退火的铜薄板、带材和板材 6 页
SAE AMS 4501D-2000(R2006) 无氧、冷轧的铜薄板、带材和板材 页
SAE AMS 4505J-2003 退火的含70Cu-30Zn铜合金（黄铜）薄板、带材和板材 5 页
SAE AMS 4507H-2001 含70Cu-30Zn的半硬铜合金（黄铜）薄板、带材和板材 5 页
SAE AMS 4508H-2000(R2006) 表面粘结的含70Cu-30Zn的铜锌合金层压薄板 页
SAE AMS 4510G-2001(R2006) 弹性回火的含94.5Cu-4.0Sn-0.19P的磷青铜薄板、带材和板材 页
SAE AMS 4511A-2004 固溶热和脱溶热处理的含97Cu-2.1Be-0.52(Co + Ni)-0.28Si铜-铍合金铸件 9 页
SAE AMS 4520J-2003 含88.5Cu-4.0Sn-4.0Pb-3.0Zn-0.26P冷轧的、半硬的铅磷青铜带材 5 页
SAE AMS 4530G-2005 固溶热处理的含98Cu-1.9Be的铜铍合金薄板、带材和板材 7 页
SAE AMS 4532F-2005 半硬质含98Cu-1.9Be的铜铍合金薄板和带材 7 页
SAE AMS 4533B-2003 固溶热和脱溶热处理的含98Cu-1.9Be的铜铍合金棒材和杆材 6 页
SAE AMS 4534B-2003 固溶热处理的、冷处理的和脱溶热处理的含98Cu-1.9Be的铜铍合金棒材和杆材 6 页
SAE AMS 4535C-2003 固溶热和脱溶热处理的含98Cu-1.9Be的铜铍合金机械管 6 页
SAE AMS 4544F-1999 退火的含67Ni-30Cu的镍铜合金耐腐蚀薄板、带材和板材 5 页
SAE AMS 4553C-2004 退火的含85Cu-15Zn的无缝黄铜管 12 页
SAE AMS 4554A-2001(R2006) 退火的含66.5Cu-33Zn-0.45Pb的无缝黄铜管 页
SAE AMS 4555H-2001(R2006) 退火的含66.5Cu-32.5Zn-0.48Pb的无缝铅黄铜管 页
SAE AMS 4558G-2004 拉制的、回火的含66.5Cu-31.5Zn-1.6Pb的无缝黄铜管 5 页
SAE AMS 4574E-2003 退火的含67Ni-31Cu的镍铜合金耐腐蚀无缝管 6 页
SAE AMS 4575D-1986(R1994) 含67Ni-31Cu退火的镍铜合金耐腐蚀钎焊管 5 页
SAE AMS 4590B-2001(R2006) 固溶热处理的和回火的含78.5Cu-10.5Al-5.1Ni-4.8Fe的马氏体镍铝青铜合金挤压件 页
SAE AMS 4596-2002 固溶退火的和亚稳界线淬硬的含77Cu-15Ni-8Sn的铜镍锡合金棒材、杆材和管 6 页
SAE AMS 4597-2006 Copper-Nickel-Tin Alloy, Bars and Rods 77Cu - 15Ni - 8Sn Solution Annealed, Cold Finished and Spinodal Hardened (TX TS) 页
SAE AMS 4602D-2003 无氧、硬质回火的铜棒材、杆材和型材 6 页
SAE AMS 4610N-2003 含61.5Cu-35Zn-3.1Pb的半硬质易切削的黄铜棒材和杆材 6 页
SAE AMS 4611H-2003 含60.5Cu-38.7Zn-0.8Sn的半硬质船用黄铜棒材和杆材 6 页
SAE AMS 4612J-2004 含60.5Cu-38.5Zn-0.75Sn的硬质回火船用黄铜棒材和杆材 6 页
SAE AMS 4614H-2003 锻造状态的含60Cu-2.0Pb-37.5Zn易切削黄铜锻件 5 页
SAE AMS 4616F-2004 消除应力的含92Cu-3.2Si-2.8Zn-1.5Fe的硅青铜棒材、杆材、锻件和管 7 页
SAE AMS 4625G-2001(R2006) 含95Cu-5Sn的硬质回火磷青铜棒材、杆材和管 页
SAE AMS 4633A-2003 拉制的和消除应力的含90Cu-7.0Al-1.8Si的铝硅青铜棒材、杆材和锻件 7 页
SAE AMS 4634A-2001(R2006) 消除应力的含90.5Cu-7.5Al-1.9Si的铝青铜棒材、杆材和锻件 页
SAE AMS 4635E-2001(R2006) 消除应力的含87Cu-9Al-3Fe的铝青铜棒材、杆材和锻件 页
SAE AMS 4640G-2005 Aluminum Bronze, Bars, Rods, Shapes, Tubes, and Forgings 81.5Cu - 10.0Al - 4.8Ni - 3.0Fe Drawn and Stress Relieved (HR50) or Temper Annealed (TQ50) Composition similar to UNS C63000 页
SAE AMS 4650L-2004 固溶热处理的TB00(A)含98Cu-1.9Be的铜铍合金棒材、杆材、型材和锻件 8 页
SAE AMS 4651C-2005 含98Cu-1.9Be(CDA 172)硬回火的铜铍合金棒材和杆材 页
SAE AMS 4674F-1999 易加工的含67Ni-30Cu-0.04S的耐腐蚀镍铜合金棒材和锻件 6 页
SAE AMS 4674G-2006 Nickel - Copper Alloy, Corrosion Resistant Bars and Forgings 67Ni - 30Cu - 0.04S Free Machining UNS N04405 页
SAE AMS 4675C-2003 含67Ni-30Cu的耐腐蚀镍铜合金棒材和锻件 6 页
SAE AMS 4676E-2003 热精加工的、脱溶硬化的含66.5Ni-3.0Al-0.62Ti-28Cu的耐腐蚀镍铜合金棒材和锻件 6 页
SAE AMS 4677B-2003 退火的含66.5Ni-2.9Al-30Cu的耐腐蚀镍铜合金棒材和锻件 6 页
SAE AMS 4700C-2000(R2006) 高纯度裸铜线 页
SAE AMS 4701F-2002 退火的含99.95(Cu+Ag)的无氧铜线 5 页
SAE AMS 4712F-2004 退火的含65Cu-35Zn的铜合金线 5 页
SAE AMS 4713F-2003 含65Cu-35Zn的黄铜线 5 页
SAE AMS 4720E-2001(R2006) 冷拉制的、弹性回火的含94Cu-5.0Sn-0.19P的磷青铜线 页
SAE AMS 4725D-1983(R2000) 含98Cu-1.9Be固溶热处理的铜-铍合金线 6 页
SAE AMS 4730E-1988(R1994) 含67Ni-31Cu退火耐腐蚀的镍-铜合金线 6 页
SAE AMS 4731B-1986(R1994) 含67Ni-31Cu退火耐腐蚀的镍-铜合金线和带 7 页
SAE AMS 4761A-1999(R2006) 固-液相线范围为1200-1330°F (649-721°C)含38Ag-32Cu-28Zn-2.0Sn的银合金钎料 页
SAE AMS 4762A-1999(R2006) 固-液相线范围为1245-1340°F (674-727°C)含40Ag-30Cu-30Zn的银合金钎料 页
SAE AMS 4763A-1999(R2006) 固-液相线范围为1145-1205°F (618-652°C)含56Ag-22Cu-17Zn-5.0Sn的银合金钎料 页
SAE AMS 4764E-1999 固-液相线范围为1615-1700°F (879-927°C)含52.5Cu-38Mn-9.5Ni的铜合金钎料 8 页
SAE AMS 4765E-1999(R2006) 固-液相线范围为1420-1640°F (771-893°C)含56Ag-42Cu-2.0Ni的银合金钎料 页
SAE AMS 4766G-1999(R2006) 固-液相线范围为1760-1780°F (960-971°C)含85Ag-15Mn的银合金钎料 页
SAE AMS 4767F-1999(R2006) 固-液相线范围为1435-1635°F (779-891°C)含92.5Ag-7.2Cu-0.22Li的银合金钎料 页
SAE AMS 4768H-1999(R2006) 固-液相线范围为1125-1295°F (607-702°C)含35Ag-26Cu-21Zn-18Cd的银合金钎料 页
SAE AMS 4769F-1999(R2006) 固-液相线范围为1125-1145°F (607-618°C)含45Ag-24Cd-16Zn-15Cu 的银合金钎料 页
SAE AMS 4770K-1999(R2006) 固-液相线范围为1160-1175°F (627-635°C)含50Ag-18Cd-16.5Zn-15.5Cu的银合金钎料 页
SAE AMS 4771H-1999(R2006) 固-液相线范围为1170-1270°F (632-688°C)含50Ag-16Cd-15.5Zn-15.5Cu-3.0Ni的银合金钎料 页
SAE AMS 4772J-1999(R2006) 固-液相线范围为1325-1575°F (718-857°C)含54Ag-40Cu-5.0Zn-1.0Ni的银合金钎料 页
SAE AMS 4773F-1999(R2006) 固-液相线范围为1115-1325°F (602-718°C)含60Ag-30Cu-10Sn的银合金钎料 页
SAE AMS 4774F-1999(R2006) 固-液相线范围为1275-1475°F (691-802°C)含63Ag-28.5Cu-6.0Sn-2.5Ni的银合金钎料 页
SAE AMS 4775H-2005 Nickel Alloy, Brazing Filler Metal 73Ni - 0.75C - 4.5Si - 14Cr - 3.1B - 4.5Fe 1790 to 1970 ? (977 to 1077 ?) Solidus-Liquidus Range UNS N99600 页
SAE AMS 4776G-2005 Nickel Alloy, Brazing Filler Metal 73Ni - 4.5Si - 14Cr - 3.1B - 4.5Fe (Low Carbon) 1790 to 1970 ? (977 to 1077 ?) Solidus-Liquidus Range UNS N99610 页
SAE AMS 4777G-2005 Nickel Alloy, Brazing Filler Metal 82Ni - 4.5Si - 7.0Cr - 3.1B - 3.0Fe 1780 to 1830 ? (971 to 999 ?) Solidus-Liquidus Range UNS N99620 页
SAE AMS 4778H-2002 固-液相线范围为1800-1900°F 含92Ni-4.5Si-3.1B的镍合金钎料 8 页
SAE AMS 4779G-2005 Nickel Alloy, Brazing Filler Metal 94Ni - 3.5Si - 1.8B 1800 to 1950 ? (982 to 1066 ?) Solidus-Liquidus Range UNS N99640 页
SAE AMS 4780E-1998 固-液相线范围为1770-1875°F (966-1024°C)含66Mn-16Ni-16Co-0.80B的锰合金钎料 6 页
SAE AMS 4782F-2005 Nickel Alloy, Brazing Filler Metal 71Ni - 10Si - 19Cr 1975 to 2075 ? (1080 to 1135 ?) Solidus-Liquidus Range UNS N99650 页
SAE AMS 4783F-2003 固-液相线范围为2050-2100°F (1121-1149°C)含50Co-8.0Si-19Cr-17Ni-4.0W-0.80B的钴合金高温钎料 7 页
SAE AMS 4784F-2001 固-液相线范围为2015-2050°F (1102-1121°C)含50Au-25Pd-25Ni的金-钯-镍合金高温钎料 9 页
SAE AMS 4785F-2001 固-液相线范围为2075-2130°F (1135-1166°C)含30Au-34Pd-36Ni的金-钯-镍合金高温钎料 9 页
SAE AMS 4786F-2001 固-液相线范围为1845-1915°F (1007-1046°C)含70Au-8.0Pd-22Ni的金-钯-镍合金高温钎料 8 页
SAE AMS 4787F-2000(R2006) Gold-Nickel Alloy, Brazing Filler Metal, High Temperature 82Au - 18Ni 1740 ? (949 ?) Solidus-Liquidus Temperature P00820 页
SAE AMS 4788A-1992(R2000) 固-液相线范围为1220-1305°F(660-707°C)含50Ag-28Zn-20Cu-2.0Ni的银合金钎料 9 页
SAE AMS 4800D-1992(R2000) 含91Sn-4.5Sb-4.5Cu的巴氏合金轴承 7 页
SAE AMS 4803D-2000(R2006) 铸造状态的含4.0Al-0.04Mg(AG40A)的锌合金模压铸件 页
SAE AMS 4805D-1986(R1994) 油浸渍的含89Cu-10Sn金属粉末烧结的轴承 5 页
SAE AMS 4820E-2003 含70Cu-28.5Pb的钢底铅铜合金轴承 5 页
SAE AMS 4827E-2004 含80Cu-10Pb-10Sn的钢底铅青铜合金轴承 5 页
SAE AMS 4842E-2004 铸造状态的含80Cu-10Sn-9.5Pb铅青铜合金砂型和离心铸件 6 页
SAE AMS 4855F-2001(R2006) 铸造状态的含85Cu-5.0Sn-5.0Pb-5.0Zn加铅的红黄铜合金砂型和离心铸件 页
SAE AMS 4860E-2001(R2006) 铸造状态的含58Cu-39Zn-1.2Fe-1.0Al-0.80Mn的锰青铜合金砂型和离心铸件 页
SAE AMS 4862F-2001(R2006) 铸造状态的含63Cu-24Zn-6.2Al-3.8Mn-3.0Fe的高强度锰青铜合金砂型和离心铸件 页
SAE AMS 4870F-2004 铸造状态的含85Cu-11Al-3.6Fe的铝青铜合金离心和冷硬铸件 8 页
SAE AMS 4871F-2000(R2006) 固溶热处理的和回火的含85Cu-11Al-3.6Fe的铝青铜合金离心和冷硬铸件 页
SAE AMS 4873F-2005 Aluminum Bronze Alloy, Sand Castings 85Cu - 11Al - 3.6Fe Solution Heat Treated and Tempered Composition similar to UNS C95420 页
SAE AMS 4880D-2005 淬火硬化和回火退火的、含81.5Cu-10.3Al-5.0Ni-2.8Fe的铝青铜合金离心和连续铸造的铸件 页
SAE AMS 4881C-2004 淬火硬化的和回火退火的含78Cu-11Al-5.1Ni-4.8Fe的马氏体镍铝青铜合金砂型和离心铸件 9 页
SAE AMS 4890C-2005 Copper-Beryllium Alloy Castings 97Cu - 2.1Be - 0.52Co - 0.28Si Solution Heat Treated (TB00) UNS C82500 页
SAE AMS 4892B-1999 铸造状态的含66Ni-29Cu-4.0Si的耐腐蚀和耐热的合金铸件 8 页
SAE AMS 4892C-2006 Alloy Castings, Corrosion and Heat Resistant 66Ni - 29Cu - 4.0Si as Cast UNS N04019 页
SAE AMS 4893B-1999 固溶处理的含66Ni-29Cu-4.0Si的耐腐蚀和耐热的合金铸件 7 页
SAE AMS 4893C-2006 Alloy Castings, Corrosion and Heat Resistant 66Ni - 29Cu - 4.0Si Solution Treated UNS N04019 页
SAE AMS 4897A-2003 含77Ti-15Mo-3.0AI-2.8Cb-0.20Si的钛合金薄板、带材和板材 9 页
SAE AMS 4898A-2001 退火的含6Al-2Sn-2Zr-2Mo-2Cr-0.15Si的钛合金薄板 7 页
SAE AMS 4899A-2003 退火的含4.5AI-3V-2Fe-2Mo的钛合金薄板、带材和板材 8 页
SAE AMS 4900L-2001 屈服强度为55.0ksi(379MPa)退火的工业纯钛薄板、带材和板材 7 页
SAE AMS 4901P-2006 Titanium Sheet, Strip, and Plate Commercially Pure Annealed, 70.0 ksi (485 MPa) UNS R50700 页
SAE AMS 4902H-2006 Titanium Sheet, Strip, and Plate Commercially-Pure Annealed 40.0 ksi (276 MPa) Yield Strength UNS R50400 页
SAE AMS 4903-2003 固溶热处理的含6Al-4V的钛合金薄板、带材和板材 9 页
SAE AMS 4904-2003 固溶热处理的和老化的含6Al-4V的钛合金薄板、带材和板材 7 页
SAE AMS 4905C-2004 含6Al-4V的二次退火耐损伤级的钛合金板材 11 页
SAE AMS 4907H-2005 Titanium Alloy, Sheet, Strip, and Plate 6.0AL - 4.0V, Extra Low Interstitial Annealed UNS R56401 页
SAE AMS 4909G-2003 含5Al-2.5Sn超低填隙的退火的钛合金薄板、带材和板材 10 页
SAE AMS 4910M-2003 含5Al-2.5Sn退火的钛合金薄板、带材和板材 9 页
SAE AMS 4911J-2003 含6AI-4V退火的钛合金薄板、带材和板材 7 页
SAE AMS 4914C-2003 含15V-3Al-3Cr-3Sn固溶热处理的钛合金冷轧薄板和带材 7 页
SAE AMS 4915J-2003 含8Al-1V-1Mo一次退火的钛合金薄板、带材和板材 9 页
SAE AMS 4916J-2006 Titanium Alloy Sheet, Strip, and Plate 8Al - 1Mo - 1V Duplex Annealed UNS R54810 页
SAE AMS 4917F-2003 含13.5V-11Cr-3.0Al固溶热处理的钛合金薄板、带材和板材 8 页
SAE AMS 4918L-2006 Titanium Alloy, Sheet, Strip, and Plate 6AI - 6V - 2Sn Annealed UNS R56620 页
SAE AMS 4919E-2003 含6Al-2Sn-4Zr-2Mo-0.08Si二次退火的钛合金薄板、带材和板材 9 页
SAE AMS 4920C-2002 经α-β或β处理的含6AI-4V退火的钛合金锻件 7 页
SAE AMS 4921K-2006 Titanium Bars, Wire, Forgings, and Rings Commercially Pure 70 ksi (483 MPa) Yield Strength UNS R50700 页
SAE AMS 4922B-2006 Titanium Alloy, Seamless, Hydraulic Tubing 15V - 3.0Cr - 3.0Al - 3.0Sn Cold Worked and Precipitation Heat Treated 页
SAE AMS 4924E-2002 含5Al-2.5Sn超低填隙的退火的钛合金棒材、锻件和环件 12 页
SAE AMS 4926K-2001 屈服强度为110 ksi(758MPa)含5Al-2.5Sn退火的钛合金棒材、线材和环件 8 页
SAE AMS 4928Q-2001 含6Al-4V退火的钛合金棒材、线材、锻件、环件和拉制的型材 9 页
SAE AMS 4930E-2001 含6Al-4V超低填隙的退火的钛合金棒材、线材、锻件和环件 8 页
SAE AMS 4931B-2002 含6Al-4V超低填隙的、二次退火的、断裂韧度的钛合金棒材、锻件和环件 9 页
SAE AMS 4932A-2002 含6Al-4V的钛合金驱动器薄板 6 页
SAE AMS 4933C-2003 固溶热处理的和稳定的含8Al-1Mo-1V钛合金挤压件和闪光焊环件 9 页
SAE AMS 4934D-2002 固溶热处理的和老化的含6Al-4V钛合金挤压件和闪光焊环件 7 页
SAE AMS 4935G-2002 经β处理的含6Al-4V退火的钛合金挤压件和闪光焊环件 7 页
SAE AMS 4937B-2006 Titanium Alloy, Extrusions and Flash Welded Rings 6Al - 6V - 2Sn Beta Extruded Plus Annealed, Heat Treatable UNS R56620 页
SAE AMS 4938-1999(R2004) 钛合金锻件热处理的、加工的部分的性能：快速横向拉伸性能、断裂韧度和纵向与时间有关的应力 21 页
SAE AMS 4939-2003 固溶热处理的含3Al-8V-6Cr-4Mo-4Zr钛合金薄板、带材和板材 9 页
SAE AMS 4940-2003 屈服强度为25.0ksi(172MPa)退火的工业纯钛薄板、带材和板材 8 页
SAE AMS 4941D-2003 屈服强度为40ksi(276MPa)退火的钛焊接管 6 页
SAE AMS 4942E-2006 Titanium Tubing, Seamless Annealed, 40.0 ksi (275 MPa) Yield Strength UNS R50400 页
SAE AMS 4943G-2003 含3.0Al-2.5V退火的钛合金液压无缝管 8 页
SAE AMS 4944F-2001 含3.0Al-2.5V冷处理的、消除应力的钛合金液压无缝管 10 页
SAE AMS 4945B-2001 含3Al-2.5V控制伸缩应变比冷处理的、消除应力的钛合金液压无缝管 12 页
SAE AMS 4946B-2006 Titanium Alloy Tubing, Seamless, Hydraulic 3Al - 2.5V, Texture Controlled Cold Worked, Stress Relieved UNS R56320 页
SAE AMS 4949-2003 表面粘结的钛层压薄板 7 页
SAE AMS 4950A-2002 固溶热处理的和老化改进强度的含6.0Al-4.0V钛合金棒材、线材、锻件和环件 10 页
SAE AMS 4951G-2003 环境受控包装的工业纯钛焊丝 7 页
SAE AMS 4952C-2003 含6Al-2Sn-4Zr-2Mo的钛合金焊丝 7 页
SAE AMS 4953D-2003 含5Al-2.5Sn的钛合金焊丝 7 页
SAE AMS 4954G-2003 含6Al-4V的钛合金焊丝 7 页
SAE AMS 4955E-2002 含8AI-1Mo-1V的钛合金焊丝 7 页
SAE AMS 4956D-2003 含6Al-4V超低填隙的环境受控包装的钛合金焊丝 7 页
SAE AMS 4957C-2003 含3Al-8V-6Cr-4Mo-4Zr自耗电极熔炼的、固溶热处理的和冷拉的钛合金圆棒材和线材 9 页
SAE AMS 4958B-2002 含3Al-8V-6Cr-4Mo-4Zr自耗电极熔炼的、固溶热处理的和无心磨削的钛合金棒材和杆材 8 页
SAE AMS 4959D-2003 弹性回火的含13.5V-11Cr-3Al的钛合金线材 7 页
SAE AMS 4963A-2003 退火的、热处理的、改进强度的含6.0Al-4.0V钛合金棒材、线材、锻件和环件 10 页
SAE AMS 4964A-2005 Titanium Alloy Bars, Wire, Forgings, and Rings 4.5Al - 3V - 2Fe - 2Mo Annealed 页
SAE AMS 4965H-2002 固溶热处理的和老化的含6.0Al-4.0V钛合金棒材、线材、锻件和环件 11 页
SAE AMS 4966M-2003 屈服强度为110ksi(758MPa)含5Al-2.5Sn退火的钛合金锻件 7 页
SAE AMS 4967H-2001 退火的、热处理的含6.0Al-4.0V钛合金棒材、线材、锻件和环件 11 页
SAE AMS 4970G-2003 固溶热和脱溶热处理的含7Al-4Mo钛合金棒材、线材和锻件 10 页
SAE AMS 4971F-2002 退火的、热处理的含6Al-6V-2Sn钛合金棒材、线材、锻件和环件 9 页
SAE AMS 4972E-2003 固溶热处理的和稳定的含8Al-1Mo-1V钛合金棒材、线材和环件 9 页
SAE AMS 4973E-2003 固溶热处理的和稳定的含8Al-1Mo-1V钛合金锻件 8 页
SAE AMS 4975H-2002 固溶热和脱溶热处理的含6.0Al-2.0Sn-4.0Zr-2.0Mo-0.08Si钛合金棒材、线材和环件 9 页
SAE AMS 4976F-2003 固溶热和脱溶热处理的含6.0Al-2.0Sn-4.0Zr-2.0Mo钛合金锻件 8 页
SAE AMS 4978D-2002 退火的含6Al-6V-2Sn钛合金棒材、线材、锻件和环件 9 页
SAE AMS 4979E-2003 固溶热和脱溶热处理的含6Al-6V-2Sn钛合金棒材、线材、锻件和环件 9 页
SAE AMS 4981D-2003 固溶热和脱溶热处理的含6.0Al-2.0Sn-4.0Zr-6.0Mo钛合金棒材、线材和锻件 9 页
SAE AMS 4982C-2002 含44.5Cb的钛合金线材 7 页
SAE AMS 4983C-2002 抗拉强度为180 ksi(1241MPa) 自耗电极熔炼的、一次固溶热处理的和老化的含10V-2Fe-3Al的钛合金锻件 9 页
SAE AMS 4984C-2003 抗拉强度为173 ksi(1193MPa) 自耗电极熔炼的、固溶热处理的和老化的含10V-2Fe-3Al的钛合金锻件 9 页
SAE AMS 4985C-2003 含6Al-4V，极限抗拉强度为130ksi，屈服强度为120ksi，延伸率为6%任选的或指定的热等压退火钛合金熔模铸件 13 页
SAE AMS 4986B-2002 抗拉强度为160 ksi(1103MPa) 自耗电极熔炼的、一次固溶热处理的和过老化的含10V-2Fe-3Al的钛合金锻件 8 页
SAE AMS 4987B-2002 抗拉强度为140 ksi(965MPa) 自耗电极熔炼的、一次固溶热处理的和过老化的含10V-2Fe-3Al的钛合金锻件 8 页
SAE AMS 4988-2003 固溶热处理的含6Al-6V-2Sn的钛合金薄板、带材和板材 9 页
SAE AMS 4989A-2006 Titanium Alloy Sheet, Strip, and Plate 3Al-2.5V Annealed UNS R56320 页
SAE AMS 4990-2003 固溶热处理的和老化的含6Al-6V-2Sn的钛合金薄板、带材和板材 8 页
SAE AMS 4991C-2002 含6Al-4V任选的热等压退火钛合金熔模铸件 21 页
SAE AMS 4992-2002 含6Al-4V的热等压钛合金结构熔模铸件 12 页
SAE AMS 4993C-2004 含6A1-4V烧结的钛合金混合粉末坯件 10 页
SAE AMS 4994A-2006(R2000) Titanium Alloy Powdered Metal Products 6Al - 4V Hot Isostatically Pressed, Annealed UNS R56400 页
SAE AMS 4998C-2003 含6Al-4V的钛合金粉末 6 页
SAE AMS 4999-2002 含6Al-4V退火的钛合金激光沉积产品 8 页
SAE AMS 5010K-2006 Steel Bars Free Machining Cold Drawn (SAE 1212 or SAE 1215) UNS G12120 页
SAE AMS 5020E-2004 含1.5Mn-0.25Pb(0.32-0.39C)(11L37)易切削的钢棒、锻件和管件 5 页
SAE AMS 5022M-2001 含0.14-0.20C(SAE 1117)易切削的钢棒、锻件和管件 7 页
SAE AMS 5024G-2001 含1.5Mn(0.32-0.39C)(SAE 1137)易切削的钢棒、锻件和管件 7 页
SAE AMS 5027E-2002 含1.05Cr-0.55Ni-1.0Mo-0.08V(0.26-0.32C)真空熔炼的环境受控包装的钢焊丝 7 页
SAE AMS 5028D-2004 含1.05Cr-0.55Ni-1.0Mo-0.07V(0.34-0.40C)真空熔炼的环境受控包装的钢焊丝 7 页
SAE AMS 5029C-2000(R2004) 含0.78Cr-1.8Ni-0.35Mo-0.20V(0.33-0.38C)真空熔炼的环境受控包装的钢焊丝 6 页
SAE AMS 5030H-2003 最大含碳量为0.06的钢焊丝 6 页
SAE AMS 5032G-2005 Wire, Steel 0.18 - 0.23C (SAE 1020) Annealed Composition similar to UNS G10200 页
SAE AMS 5034A-2006 Steel, Welding Wire 0.95Cr - 0.20Mo (0.28 - 0.33C) (SAE 4130) UNS G41300 页
SAE AMS 5035A-2006 Steel, Welding Wire 0.65Si - 1.25Cr - 0.50Mo - 0.30V (0.28 - 0.33C) UNS K23015 页
SAE AMS 5040M-2006 Steel, Sheet and Strip 0.15 Carbon, Maximum Deep Forming Grade UNS G10100 页
SAE AMS 5042L-2003 最大含碳量为0.15的成形级钢薄板和带材 4 页
SAE AMS 5044J-2005 Steel, Sheet and Strip 0.15 Carbon, Maximum Half Hard Temper UNS G10100 页
SAE AMS 5045H-2005 Steel, Sheet and Strip 0.25 Carbon, Maximum Hard Temper UNS G10200 页
SAE AMS 5046B-2001 退火的碳钢薄板、带材和板材(SAE 1020 和 1025) 6 页
SAE AMS 5047E-2001 含0.08-0.13C的深成形级铝脱氧钢薄板和带材 5 页
SAE AMS 5050K-2001(R2006) 最大含碳量为0.15退火的无缝钢管 页
SAE AMS 5053H-2001(R2006) 最大含碳量为0.13退火的焊接钢管 页
SAE AMS 5060H-2003 含0.13-0.18C的钢棒材、锻件和管件 5 页
SAE AMS 5061F-2004 含0.08-0.20C的低碳钢棒和钢丝 5 页
SAE AMS 5062G-2004 最大含碳量为0.25的低碳钢棒、锻件、钢管、薄板、带材和板材 5 页
SAE AMS 5069F-2001(R2006) 含0.15-0.20C的钢棒材、锻件和管件(SAE 1018) 页
SAE AMS 5070H-2001(R2006) 含0.18-0.23C的钢棒材和锻件(SAE 1022) 页
SAE AMS 5075F-2001(R2006) 含0.22-0.28C冷拉和消除应力的无缝钢管(SAE 1025) 页
SAE AMS 5077F-2001(R2006) 含0.22-0.28C正火或消除应力的焊接钢管(SAE 1025) 页
SAE AMS 5080J-2001(R2006) 含0.31-0.38C的钢棒材、锻件和管件(SAE 1035) 页
SAE AMS 5082F-2003 含0.31-0.38C消除应力的无缝钢管(SAE 1035) 5 页
SAE AMS 5085F-2003 含0.47-0.55C退火的钢薄板、带材和板材(SAE 1050) 6 页
SAE AMS 5110H-2001 含0.75-0.88C弹性回火、冷拉的碳钢丝和碳钢弹簧(SAE 1080) 6 页
SAE AMS 5112L-2003 含0.70-1.00C冷拉的优质琴用碳钢弹簧丝 9 页
SAE AMS 5120K-2001 含0.68-0.80C的钢带材(SAE 1074) 5 页
SAE AMS 5121J-2006 Sheet and Strip, Steel (0.90 - 1.04C) (SAE 1095) Annealed UNS G10950 页
SAE AMS 5122H-2003 含(0.90-1.04C)硬质回火的钢带(SAE 1095) 5 页
SAE AMS 5132J-2003 含0.90-1.30C的钢棒材 5 页
SAE AMS 5221E-2001(R2006) 固溶热处理的含49Fe-5.3Cr-42Ni-2.5Ti-0.55Al的铁-镍合金带材 页
SAE AMS 5223F-2002 固溶热处理的、10%冷轧压缩、含49Fe-5.3Cr-42Ni-2.5Ti-0.55Al的铁-镍合金带材 6 页
SAE AMS 5225E-2000(R2006) 固溶热处理的、50%冷轧压缩、含49Fe-5.3Cr-42Ni-2.5Ti-0.55Al的铁-镍合金带材 页
SAE AMS 5333E-2002 含0.50Cr-0.55Ni-0.25Mo(0.11-0.17C)正火的钢熔模铸件(SAE 8615) 8 页
SAE AMS 5334G-2002 含0.50Cr-0.55Ni-0.20Mo(0.25-0.35C)正火的和回火的钢熔模铸件(SAE 8630 修改) 11 页
SAE AMS 5336F-2001(R2006) 含0.95Cr-0.20Mo(0.25-0.35C)正火的或正火的和回火的钢熔模铸件(SAE 4130 修改) 页
SAE AMS 5337C-2001 真空熔炼均质化、过老化的和固溶热处理的含18.5Ni-9.0Co-5.0Mo-0.70Ti-0.12Al的马氏体钢熔模铸件 11 页
SAE AMS 5338E-2001(R2006) 含0.95Cr-0.20Mo(0.35-0.45C)正火的或正火的和回火的钢熔模铸件(SAE 4140 修改) 页
SAE AMS 5339E-2001 真空熔炼均质化、过老化的和固溶热处理的含17Ni-10Co-4.6Mo-0.30Ti-0.06Al的马氏体钢熔模铸件 12 页
SAE AMS 5340D-1997 均质化和固溶热处理的含14Cr-4.25Ni-2.25Mo-0.25Cb-3.25Cu耐腐蚀的钢熔模铸件 13 页
SAE AMS 5342E-2006 Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb (Nb) - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1100) 130 ksi (896 MPa) Tensile Strength (17-4) UNS J91280 and UNS J92200 页
SAE AMS 5343E-2006 Steel, Corrosion-Resistant, Investmment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength UNS J92200; UNS J92180 页
SAE AMS 5344E-2006 Steel, Corrosion-Resistant, Investment Castings 16Cr - 4.1Ni - 0.28Cb - 3.2Cu Homogenization, Solution, and Precipitation Heat Treated (H900) 180 ksi (1241 MPa) Tensile Strength UNS J92180 and J92200 页
SAE AMS 5346C-2006 Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H925) 180 ksi (1241 MPa) Tensile Strength (15-5) UNS J92110 页
SAE AMS 5347B-2006 Steel, Corrosion-Resistant, Investment Castings 15Cr - 4.6Ni - 0.22Cb (Nb) - 2.8Cu Solution and Precipitation Heat Treated (H1000) 150 ksi (1034 MPa) Tensile Strength (15-5) UNS J92110 页
SAE AMS 5349C-2000 淬硬和回火的含13Cr易切削耐腐蚀的钢熔模铸件 13 页
SAE AMS 5350H-2001(R2006) 淬硬和回火的含12.5Cr耐腐蚀和耐中温的钢熔模铸件(SAE 51410) 页
SAE AMS 5352D-2000 退火的含17Cr-0.55Mo(0.95-1.20C)耐腐蚀的钢熔模铸件 11 页
SAE AMS 5353C-2000 铸造状态的含16Cr-1.8Ni-0.08N耐腐蚀的钢熔模铸件 13 页
SAE AMS 5354E-2001(R2006) 淬硬和回火的含13Cr-2.0Ni-3.0W耐腐蚀和耐热的钢熔模铸件 页
SAE AMS 5355H-2001(R2006) 均质化和固溶热处理的或均质化、固溶热和脱溶热处理的含16Cr-4.1Ni-0.28Cb-3.2Cu耐腐蚀的钢熔模铸件 页
SAE AMS 5356B-2001(R2006) 固溶热和脱溶热处理的(H1100)、抗拉强度为130ksi(896MPa)含15Cr-4.6Ni-0.22Cb-2.8Cu耐腐蚀的钢熔模铸件 页
SAE AMS 5357B-2001(R2006) 固溶热处理的、脱溶淬硬的含15Cr-4.6Ni-0.22Cb-2.8Cu耐腐蚀的钢熔模铸件 页
SAE AMS 5360F-2004 固溶热处理的含17Cr-13Ni-1.9Mo耐腐蚀和耐热的钢熔模铸件 10 页
SAE AMS 5362K-2001(R2006) 固溶热处理的含19Cr-12Ni-1.0(Cb+Ta)耐腐蚀和耐热的钢熔模铸件 页
SAE AMS 5364C-2004 固溶热处理的含19.5Cr-10.5Ni-0.65Cb(CF-8C)耐腐蚀和耐热的钢熔模铸件 11 页
SAE AMS 5366E-2004 铸造状态的含25Cr-20Ni(CK-20)耐腐蚀和耐热的钢熔模铸件 10 页
SAE AMS 5368D-2004 固溶热处理的含15Cr-4.0Ni-2.3Mo-0.09N耐腐蚀的钢熔模铸件 12 页
SAE AMS 5370D-2004 固溶热处理的含19Cr-9.5Ni(CF-3)耐腐蚀和耐热的钢熔模铸件 11 页
SAE AMS 5376G-2002 铸造状态的含30Fe-21Cr-20Ni-20Co-3.0Mo-2.5W-1.0Cb-0.15N耐腐蚀和耐热的熔模合金铸件 11 页
SAE AMS 5377F-2004 铸造状态、真空铸造的含73Ni-12Cr-4.5Mo-2.0Cb-0.70Ti-0.05C-6.0Al-0.010B-0.10Zr耐腐蚀和耐热的镍合金熔模铸件 11 页
SAE AMS 5380F-1999 铸造状态的含50.5Co-26Cr-15Ni-6.0Mo耐腐蚀和耐热的钴合金熔模铸件 11 页
SAE AMS 5382H-1993(R2000) 铸造状态的含54Co-25.5Cr-10.5Ni-7.5W耐腐蚀和耐热的钴合金熔模铸件 12 页
SAE AMS 5382J-2006 Cobalt Alloy, Corrosion and Heat Resistant, Investment Castings 54Co - 25.5Cr - 10.5Ni - 7.5W as Cast UNS R30031 页
SAE AMS 5383D-1993(R2000) 真空熔炼的、均质化和固溶热处理的含52.5Ni-19Cr-3.0Mo-5.1(Cb+Ta)-0.90Ti-0.60Al-18Fe耐腐蚀和耐热的镍合金熔模铸件 14 页
SAE AMS 5385G-1999 铸造状态的含62Co-27Cr-2.8Ni-5.5Mo耐腐蚀和耐热的钴合金熔模铸件 11 页
SAE AMS 5387C-2001(R2006) 铸造状态的含60Co-29Cr-4.5W耐腐蚀和耐热的熔模合金铸件 页
SAE AMS 5388H-2005 铸造状态、含53.3Ni-16.5Cr-17Mo-4.5W-5.8Fe-0.40V(CW-12MW)的耐腐蚀和耐热的镍合金熔模铸件 页
SAE AMS 5390E-2005 铸造状态的含47.5Ni-22Cr-1.5Co-9Mo-0.60W-18.5Fe(N-12MV)耐腐蚀和耐热的镍合金熔模铸件 11 页
SAE AMS 5391F-2005 真空铸造、铸造状态的含73Ni-0.14C-13Cr-4.5Mo-2.3Cb-0.75Ti-6.0Al-0.010B-0.10Zr耐腐蚀和耐热的镍合金熔模铸件 11 页
SAE AMS 5396D-2005 铸造状态的含65Ni-28Mo-5.5Fe-0.40V(N-12MV)耐腐蚀和耐热的镍合金熔模铸件 11 页
SAE AMS 5398F-2006 Steel, Corrosion Resistant, Sand and Centrifugal Castings 16Cr - 4.1Ni - 0.22(Cb + Ta) - 2.8Cu Solution Heat Treated UNS J92200 页
SAE AMS 5399C-1993(R2000) 真空熔炼的、真空铸造和固溶热处理的含52Ni-19Cr-11Co-9.8Mo-3.2Ti-1.6Al-0.006B耐腐蚀和耐热的镍合金熔模铸件 13 页
SAE AMS 5399D-2006 Nickel Alloy, Corrosion and Heat Resistant, Investment Castings 52Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum-Melted, Vacuum-Cast, Solution Heat Treated UNS N07041 页
SAE AMS 5400A-1995 固溶热和脱溶热处理的(H935)、抗拉强度为170ksi(1172MPa)含15Cr-4.6Ni-0.22Cb-2.8Cu耐腐蚀的钢熔模铸件 13 页
SAE AMS 5401C-2004 铸造状态的含62Ni-21.5Cr-9.0Mo-3.6Cb(Nb)真空熔炼、真空铸造耐腐蚀和耐热的镍合金熔模铸件 11 页
SAE AMS 5402C-2004 铸造状态的含62Ni-21.5Cr-9.0Mo-3.6Cb(Nb)耐腐蚀和耐热的镍合金熔模铸件 12 页
SAE AMS 5410A-2001(R2006) 铸造状态的或固溶处理的或固溶和脱溶淬硬的含61Ni-16Cr-8.5Co-1.8Mo-2.6W-0.85Cb-3.4Ti-1.8Ta-3.4Al-0.010B-0.05Zr真空熔炼、真空铸造耐腐蚀和耐热的镍合金熔模铸件 页
SAE AMS 5412-1990(R2000) 均质化、固溶热和脱溶热处理的含13Cr-8.0Ni-2.2Mo-1.1Al抗拉强度为195,000 psi(1344MPa)(条件H1000)真空熔炼的、真空铸造耐腐蚀的钢熔模铸件 10 页
SAE AMS 5500E-2002 表面粘结的耐腐蚀的钢层压薄板 7 页
SAE AMS 5501E-2002 冷轧的、抗拉强度为125 ksi(862MPa)含19Cr-9.5Ni(304)耐腐蚀的钢薄板、带材和箔 5 页
SAE AMS 5503E-2006 Steel, Corrosion-Resistant, Sheet, Strip, and Plate 17Cr (SAE 51430) Annealed UNS S43000 页
SAE AMS 5504M-2002 退火的含12.5Cr(SAE 51410)耐腐蚀和耐热的钢薄板、带材和板材 6 页
SAE AMS 5505E-2001 铁素体受控的、退火的含12Cr(SAE 51410修改)耐腐蚀和耐热的钢薄板、带材和板材 6 页
SAE AMS 5506F-2001 退火的含13Cr(0.30-0.40C)(SAE 51420)耐腐蚀和耐热的钢薄板、带材和板材 5 页
SAE AMS 5507F-2002 固溶热处理的含17Cr-13Ni-2.5Mo(SAE 30316L)耐腐蚀和耐热的钢薄板、带材和板材 5 页
SAE AMS 5508F-2001(R2006) Steel, Corrosion and Heat Resistant, Sheet, Strip, and Plate 13Cr - 2.0Ni - 3.0W Annealed UNS S41800 页
SAE AMS 5510R-2003 固溶热处理的含18Cr-10.5Ni-0.40Ti(SAE 30321)耐腐蚀和耐热的钢薄板、带材和板材 6 页
SAE AMS 5511H-2003 固溶热处理的含19Cr-9.5Ni(304L)耐腐蚀的钢薄板、带材和板材 5 页
SAE AMS 5512K-2000 固溶热处理的含18Cr-10.5Ni-0.80Cb耐腐蚀和耐热的钢薄板、带材和板材(SAE 30347) 7 页
SAE AMS 5513H-2004 固溶热处理的含19Cr-9.2Ni耐腐蚀的钢薄板、带材和板材(SAE 30304) 6 页
SAE AMS 5514G-2000 固溶热处理的含18Cr-11.5Ni耐腐蚀的钢薄板、带材和板材(SAE 30305) 6 页
SAE AMS 5515L-2002 固溶热处理的、高含18Cr-8.5Ni(302)耐腐蚀的钢薄板、带材和板材 5 页
SAE AMS 5516N-2006 Steel, Corrosion-Resistant, Sheet, Strip, and Plate 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated UNS S30200 页
SAE AMS 5517L-2000(R2006) 冷轧的、抗拉强度为125ksi(862MPa)含18Cr-8Ni耐腐蚀的钢薄板和带材(SAE 30301) 页
SAE AMS 5518K-2003 冷轧的、抗拉强度为150ksi(1034MPa)含18Cr-8Ni耐腐蚀的钢薄板和带材(SAE 30301) 5 页
SAE AMS 5519M-2003 冷轧的、抗拉强度为185ksi(1276MPa)含18Cr-8Ni耐腐蚀的钢薄板和带材(SAE 30301) 5 页
SAE AMS 5520F-2003 固溶热处理的、脱溶淬硬的含15Cr-7.1Ni-2.5Mo-1.1Al耐腐蚀和耐热的钢薄板、带材、箔和板材 8 页
SAE AMS 5521G-1994(R2000) 固溶热处理的含25Cr-20Ni耐腐蚀和耐热的钢薄板、带材和板材(SAE 30310S) 7 页
SAE AMS 5523E-1994(R2000) 固溶热处理的含23Cr-13.5Ni耐腐蚀和耐热的钢薄板、带材和板材(SAE 30309S) 7 页
SAE AMS 5523F-2006 Steel, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 23Cr - 13.5Ni (SAE 30309S) Solution Heat Treated UNS S30908 页
SAE AMS 5524K-2003 固溶热处理的含18Cr-13Ni-2.5Mo耐腐蚀和耐热的钢薄板、带材和板材(SAE 30316) 6 页
SAE AMS 5525H-2001(R2006) 1800°F (982°C)固溶热处理的含15Cr-25.5Ni-1.2Mo-2.1Ti-0.006B-0.30V耐腐蚀和耐热的钢薄板、带材和板材 页
SAE AMS 5528F-1994(R2000) 固溶热处理的、脱溶淬硬的含17Cr-7.1Ni-1.1A1耐腐蚀的钢薄板、带材和板材 8 页
SAE AMS 5529G-2003 额定厚度为0.0015-0.050英寸(0.038-1.27mm)固溶热处理的和冷轧、脱溶淬硬的含17Cr-7.1Ni-1.1Al耐腐蚀的钢薄板和带材 6 页
SAE AMS 5532F-1995 固溶热处理的含30Fe-21Cr-20Ni-20Co-3.0Mo-2.5W-1.0Cb-0.15N耐腐蚀和耐热的铁合金薄板、带材和板材 7 页
SAE AMS 5532G-2006 Iron Alloy, Corrosion and Heat Resistant, Sheet, Strip, and Plate 30Fe - 21Cr - 20Ni - 20Co - 3.0Mo - 2.5W - 1.0Cb - 0.15N Solution Heat Treated UNS R30155 页
SAE AMS 5536L-1993(R2006) 固溶热处理的含47.5Ni-22Cr-1.5Co-9.0Mo-0.60W-18.5Fe耐腐蚀和耐热的镍合金薄板、带材和板材 页
SAE AMS 5537H-2002 固溶热处理的含52Co-20Cr-10Ni-15W耐腐蚀和耐热的钴合金薄板、带材、箔和板材 6 页
SAE AMS 5540M-2006 Nickel Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 74Ni - 15.5Cr - 8.0Fe Annealed UNS N06600 页
SAE AMS 5541F-2000 退火的含73Ni-15.5Cr-2.4Ti-0.7Al-7.0Fe耐腐蚀和耐热的镍合金薄板和带材 6 页
SAE AMS 5542L-1994(R2000) 退火的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70A1-7.0Fe耐腐蚀和耐热的镍合金薄板、带材和板材 9 页
SAE AMS 5544H-2001(R2006) 自耗电极或真空感应熔炼的、退火的含57Ni-19.5Cr-13.5Co-4.2Mo-3.0Ti-1.4Al-0.05Zr-0.006B耐腐蚀和耐热的镍合金薄板、带材和板材 页
SAE AMS 5545E-2002 真空感应和自耗电极熔炼的、固溶热处理的、脱溶热处理的含54Ni-19Cr-11Co-9.8Mo-3.2Ti-1.5Al-0.006B耐腐蚀和耐热的镍合金薄板、带材和板材 8 页
SAE AMS 5547G-2000 固溶热处理的含15.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢薄板和带材 7 页
SAE AMS 5547H-2006 Steel, Corrosion and Heat Resistant, Sheet and Strip 15.5 Cr - 4.5Ni - 2.9Mo - 0.10N Solution Heat Treated UNS S35500 页
SAE AMS 5548M-2000 1850-1975°F(1010-1079°C)退火的含16.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢薄板和带材 9 页
SAE AMS 5548N-2006 Steel, Corrosion and Heat Resistant, Sheet and Strip 16.5Cr - 4.5Ni - 2.9Mo - 0.10N 1850 to 1975 Degrees F (1010 to 1079 Degrees C) Annealed UNS S35000 页
SAE AMS 5552F-2006(R2000) Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 46Fe - 20.5Cr - 32Ni - 1.1Ti Annealed 页
SAE AMS 5553F-2001 退火的低碳(最大含碳量为0.02)镍薄板和带材 5 页
SAE AMS 5554D-2000 退火的含16.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的无缝钢管 7 页
SAE AMS 5555D-2006 Nickel Wire and Ribbon 99Ni UNS N02205 页
SAE AMS 5556H-2003 固溶热处理的含18Cr-11Ni-0.70Cb耐腐蚀和耐热的无缝或焊接液压钢管(SAE 30347) 8 页
SAE AMS 5557J-2002 固溶热处理的含18.5Cr-10.5Ni-0.40Ti耐腐蚀和耐热的无缝或焊接液压钢管(SAE 30321) 9 页
SAE AMS 5558G-2003 固溶热处理的含18Cr-10.5Ni-0.70Cb耐腐蚀和耐热的薄壁焊接钢管(SAE 30347) 9 页
SAE AMS 5559J-2002 固溶热处理的含18Cr-10.5Ni-0.40Ti耐腐蚀和耐热的薄壁焊接钢管(SAE 30321) 9 页
SAE AMS 5560L-2001(R2006) 固溶热处理的含19Cr-10Ni耐腐蚀的无缝钢管(SAE 30304) 页
SAE AMS 5561F-1999 含9.0Mn-20Cr-6.5Ni-0.28N耐腐蚀和耐热的焊接和拉制或无缝和拉制高液压钢管 11 页
SAE AMS 5562D-2001(R2006) 固溶热处理的含9.0Mn-20Cr-6.5Ni-0.28N耐腐蚀和耐热的无缝钢管 页
SAE AMS 5563C-2002 冷拉制、1/4硬回火的含19Cr-9.5Ni耐腐蚀的无缝或焊接钢管(SAE 30304) 6 页
SAE AMS 5564C-2000 含19Cr-10Ni高液压焊接加超声检测或无缝冷拉制、1/8硬回火的耐腐蚀钢管(SAE 30304) 10 页
SAE AMS 5565K-2001(R2006) 固溶热处理的含19Cr-9.5Ni耐腐蚀的焊接钢管(SAE 30304) 页
SAE AMS 5566L-2001(R2006) 高压、冷拉制的含19Cr-10Ni耐腐蚀的无缝或焊接液压钢管(SAE 30304) 页
SAE AMS 5567E-2002 固溶热处理的含19Cr-10Ni耐腐蚀的无缝或焊接液压钢管(SAE 30304) 8 页
SAE AMS 5568F-2001(R2006) 固溶热处理的、脱溶淬硬的含17Cr-7.1Ni-1.1Al耐腐蚀和耐热的焊接钢管 页
SAE AMS 5569A-2001(R2006) 冷拉制、1/8硬回火的含19Cr-9.5Ni-0.03C(最大)耐腐蚀和耐热的无缝和焊接液压钢管 页
SAE AMS 5570P-2006 Steel, Corrosion and Heat-Resistant, Seamless Tubing 18Cr - 11Ni - 0.40Ti (SAE 30321) Solution Heat Treated UNS S32100 页
SAE AMS 5571G-1993(R2000) 固溶热处理的含18Cr-10.5Ni-0.70Cb耐腐蚀和耐热的无缝钢管(SAE 30347) 8 页
SAE AMS 5572H-2002 固溶热处理的含25Cr-20Ni耐腐蚀和耐热的无缝钢管(SAE 30310S) 7 页
SAE AMS 5573L-2002 固溶热处理的含17Cr-12Ni-2.5Mo耐腐蚀和耐热的无缝钢管(SAE 30316) 7 页
SAE AMS 5574E-2001(R2006) 固溶热处理的含23Cr-13.5Ni耐腐蚀和耐热的无缝钢管(SAE 30309S) 页
SAE AMS 5575M-2000 固溶热处理的含18Cr-10.5Ni-0.70Cb耐腐蚀和耐热的焊接钢管(SAE 30347) 9 页
SAE AMS 5576K-2005 Steel, Corrosion and Heat-Resistant, Welded Tubing 18Cr - 10.5Ni - 0.40Ti (SAE 30321) Solution Heat Treated UNS S32100 页
SAE AMS 5577H-2001(R2006) 固溶热处理的含25Cr-20Ni耐腐蚀和耐热的焊接钢管(SAE 30310) 页
SAE AMS 5578G-2003 真空感应加自耗电极真空熔炼的、固溶热处理的、脱溶淬硬的含12Cr-8.5Ni-0.30Cb-1.1Ti-2.0Cu耐腐蚀和耐热的焊接钢管 7 页
SAE AMS 5580K-2006 Nickel Alloy, Corrosion and Heat Resistant, Seamless Tubing 74Ni - 15.5Cr - 8.0Fe Annealed UNS N06600 页
SAE AMS 5581D-2001 退火的含62Ni-21.5Cr-9.0Mo-3.7Cb耐腐蚀和耐热的镍合金无缝或焊接管 7 页
SAE AMS 5582E-2002 固溶热处理的、脱溶淬硬的抗拉强度为155ksi(1069MPa)含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金无缝管 7 页
SAE AMS 5583D-2002 真空熔炼的、固溶热处理的、脱溶淬硬的抗拉强度为170ksi(1172MPa)含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金无缝管 7 页
SAE AMS 5584A-2000(R2006) 冷拉制、1/8硬回火的含17Cr-12Ni-1.5Mo-0.03C(最大)耐腐蚀和耐热的无缝和焊接液压钢管 页
SAE AMS 5585F-2001(R2006) 固溶热处理的含32Fe-21Cr-20Ni-20Co-3Mo-2.5W-1.0Cb-0.15N耐腐蚀和耐热的合金焊接管 页
SAE AMS 5586F-2001 自耗电极或真空感应熔炼的、退火的含57Ni-19.5Cr-13.5Co-4.2Mo-2.9Ti-1.4Al-0.006B-0.08Zr耐腐蚀和耐热的镍合金焊接管 8 页
SAE AMS 5587E-2001(R2006) 固溶热处理的含47.5Ni-22Cr-1.5Co-9.0Mo-0.60W-18.5Fe耐腐蚀和耐热的镍合金无缝管 页
SAE AMS 5588F-2000(R2006) 固溶热处理的含47.5Ni-22Cr-1.5Co-9.0Mo-0.60W-18.5Fe耐腐蚀和耐热的镍合金焊接管 页
SAE AMS 5589D-2000 自耗电极或真空感应熔炼的、1775°F (968°C)固溶热处理的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50A1-18Fe耐腐蚀和耐热的镍合金无缝管 9 页
SAE AMS 5590E-2000(R2006) 自耗电极或真空感应熔炼的、1950°F (1066°C)固溶热处理的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50A1-18Fe耐腐蚀和耐热的镍合金无缝管 页
SAE AMS 5591K-2006 Steel, Corrosion and Heat-Resistant, Tubing, Seamless 12.5Cr (SAE 51410) Annealed UNS S41000 页
SAE AMS 5592E-2002 固溶热处理的含44Fe-18.5Cr-35Ni-1.15Si耐腐蚀和耐热的铁-镍合金薄板、带材和板材 6 页
SAE AMS 5593F-2001(R2006) 固溶热处理的含45.5Ni-25.5Cr-3.2Co-3.2Mo-3.2W-18.5Fe耐腐蚀和耐热的镍合金薄板、带材和板材 页
SAE AMS 5595F-2001(R2006) 固溶热处理的含9.0Mn-20Cr-6.5Ni-0.28N耐腐蚀的钢薄板、带材和板材 页
SAE AMS 5596J-1999 自耗电极或真空感应熔炼的、1775°F (968°C)固溶热处理的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50A1-18Fe耐腐蚀和耐热的镍合金薄板、带材、箔和板材 12 页
SAE AMS 5597E-2001(R2006) 自耗电极或真空感应熔炼的、1950°F (1066°C)固溶热处理的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50A1-18Fe耐腐蚀和耐热的镍合金薄板、带材和板材 页
SAE AMS 5598D-2000 自耗电极或真空感应熔炼的、固溶热处理的、脱溶淬硬的含72Ni-15.5Cr-0.95(Cb + Ta)-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金薄板、带材和板材 8 页
SAE AMS 5599F-2000 退火的含62Ni-21.5Cr-9.0Mo-3.7(Cb+Ta)耐腐蚀和耐热的镍合金薄板、带材和板材 7 页
SAE AMS 5600D-1992(R2000) 边缘粘结的耐腐蚀层压钢薄板 5 页
SAE AMS 5604E-2001 固溶热处理的、脱溶淬硬的含16.5Cr-4.0Ni-4.0Cu-0.30Cb耐腐蚀的钢薄板、带材和板材 8 页
SAE AMS 5605D-2000 自耗电极或真空感应熔炼的、1800°F (982°C)固溶热处理的含41.5Ni-16Cr-37Fe-2.9Cb-1.8Ti耐腐蚀和耐热的镍合金薄板、带材和板材 7 页
SAE AMS 5606E-2000 Alloy, Corrosion and Heat-Resistant, Sheet, Strip, and Plate 41.5Ni - 16Cr - 37Fe - 2.9Cb - 1.8Ti Consumable Electrode or Vacuum Induction Melted 1750 ? (954 ?) Solution Heat Treated UNS N09706 页
SAE AMS 5607E-2002 固溶热处理的含73Ni-7.0Cr-16.5Mo耐腐蚀和耐热的镍合金薄板、带材和板材 6 页
SAE AMS 5608E-2001(R2006) 固溶热处理的含40Co-22Cr-22Ni-14.5W-0.07La耐腐蚀和耐热的钴合金薄板、带材和板材 页
SAE AMS 5609D-1999 铁素体受控的、退火的含12Cr-0.12Cb(SAE 51410修改)耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 9 页
SAE AMS 5610N-2000 Steel, Corrosion and Heat-Resistant, Bars, Wire, and Forgings 12.5Cr - Low Carbon (SAE 51416, 51416Se) Free-Machining UNS S41600 and S41623 页
SAE AMS 5611E-2000 铁素体受控的、自耗电极熔炼的含12Cr耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 9 页
SAE AMS 5611F-2006 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Consumable Electrode Melted UNS S41001 页
SAE AMS 5612G-2000 铁素体受控的、退火的含12Cr耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 9 页
SAE AMS 5612H-2006 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 12Cr Ferrite Controlled, Annealed UNS S41001 页
SAE AMS 5613R-2001 退火的含12.5Cr耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 51410) 6 页
SAE AMS 5614E-2001 退火的含12Cr-0.50Mo耐腐蚀和耐热的钢棒、钢丝和锻件 6 页
SAE AMS 5616L-2003 退火的含13Cr-2.0Ni-3.0W耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 7 页
SAE AMS 5617J-2006 Steel Bars, Wire, and Forgings, Corrosion Resistant 12Cr - 8.5Ni - 1.2Ti - 2.0Cu Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable UNS S45500 页
SAE AMS 5618G-2006 Steel, Corrosion Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) (SAE 51440C) Consumable Electrode Vacuum Melted UNS S44004 页
SAE AMS 5620F-1999 含13Cr(0.30 - 0.40C)易切削耐腐蚀和耐热的钢棒、钢丝和锻件(SAE 51420F, 51420Se) 8 页
SAE AMS 5620G-2006 Steel, Corrosion and Heat Resistant, Bars, Wire,and Forgings 13Cr (0.30 - 0.40C) (SAE 51420F, 51420Se) Free-Machining Grade UNS S42020 (Type 2); S42023 (Type 1) 页
SAE AMS 5621E-2001(R2006) 退火的含13Cr(0.30 - 0.40C)耐腐蚀的钢棒、钢丝和锻件(SAE 51420) 页
SAE AMS 5622D-2002(R2004) 固溶热处理的、脱溶淬硬的含16Cr-4.0Ni-0.30Cb-4.0Cu耐腐蚀的钢棒、钢丝、锻件、钢管和环件 11 页
SAE AMS 5627G-2003 退火的含17Cr耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 51430) 6 页
SAE AMS 5628F-2002 含16Cr-2.5Ni耐腐蚀的钢棒、钢丝、锻件和钢管(SAE 51431) 13 页
SAE AMS 5629E-2002 真空感应加自耗电极熔炼的、固溶热处理的、脱溶淬硬的含13Cr-8.0Ni-2.2Mo-1.1Al耐腐蚀的钢棒、钢丝、锻件、环件和挤压件 11 页
SAE AMS 5630H-2006 Steel, Corrosion Resistant, Bars, Wire, and Forgings 17Cr - 0.52Mo (0.95 - 1.20C) (SAE 51440C) (UNS S44004) 页
SAE AMS 5631D-2000 含17Cr(0.60-0.75C)耐腐蚀的钢棒和锻件(SAE 51440A) 7 页
SAE AMS 5631E-2006 Steel, Corrosion Resistant, Bars and Forgings 17Cr (0.60 - 0.75C) UNS S44002 页
SAE AMS 5632H-2006 Steel, Corrosion-Resistant, Bars, Wire, and Forgings 17Cr - 0.50Mo (0.95 - 1.20C) (SAE 51440F) Free-Machining, Annealed UNS S44020 (Type I) or UNS S44023 (Type II) 页
SAE AMS 5635E-2001 固溶热处理的含18Cr-9Ni-0.21Pb(303Pb)易切削耐腐蚀的钢棒、钢丝和锻件 7 页
SAE AMS 5636F-2006 Steel, Corrosion-Resistant, Bars and Wire 18Cr - 9.0Ni (SAE 30302) Solution Heat Treated and Cold Drawn 100 ksi (689 MPa) Tensile Strength UNS S30200 页
SAE AMS 5637G-2001(R2006) 固溶热处理的和冷拉制的抗拉强度为125ksi(862MPa)含18Cr-9.0Ni耐腐蚀的钢棒和钢丝(SAE 30302) 页
SAE AMS 5638F-2005 Steel, Corrosion-Resistant, Bars and Forgings 0.14S - 18Cr - 9.5Ni - 0.50Mo - 0.80Al (303MA) Free-Machining; Swaging or Upsetting Solution Heat Treated Composition similar to UNS S30345 页
SAE AMS 5639H-2002 固溶热处理的含19Cr-10Ni耐腐蚀的钢棒、钢丝、锻件、钢管和环件 7 页
SAE AMS 5640T-2003 含18Cr-9.0Ni易切削耐腐蚀的钢棒、钢丝和锻件 7 页
SAE AMS 5641F-1992(R2000) 含18.5Cr-10Ni-0.22Se易切削、型锻或镦锻、固溶热处理耐腐蚀的钢棒、钢丝和锻件(SAE 30303Se) 8 页
SAE AMS 5642K-2002 含18Cr-10.5Ni-0.60Cb易切削、固溶热处理的、耐腐蚀和耐热的钢棒、钢丝和锻件 6 页
SAE AMS 5643Q-2003 固溶热处理的、脱溶淬硬的含16Cr-4.0Ni-0.30Cb-4.0Cu耐腐蚀的钢棒、钢丝、锻件、钢管和环件 8 页
SAE AMS 5645P-2001(R2006) 固溶热处理的含18Cr-10Ni-0.40Ti耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 30321) 页
SAE AMS 5646M-2002 固溶热处理的含18Cr-11Ni-0.60Cb耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 30347) 7 页
SAE AMS 5647H-2002 固溶热处理的含19Cr-9.5Ni耐腐蚀的钢棒、钢丝、锻件、钢管和环件 7 页
SAE AMS 5648K-2002 固溶热处理的含17Cr-12Ni-2.5Mo耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 7 页
SAE AMS 5649G-2002 固溶热处理的含18Cr-13Ni-2.1Mo易切削耐腐蚀和耐热的钢棒、钢丝和锻件 6 页
SAE AMS 5650E-1995 固溶热处理的含23Cr-13.5Ni耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 30309S) 8 页
SAE AMS 5650F-2006 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 23Cr - 13.5Ni (SAE 30309S) Solution Heat Treated UNS S30908 页
SAE AMS 5651J-2003 固溶热处理的含25Cr-20Ni耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件(SAE 30310) 6 页
SAE AMS 5652G-2001(R2006) Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 25Cr - 20Ni - 2.0Si (SAE 30314) Solution Heat Treated UNS S31400 页
SAE AMS 5653F-2002 固溶热处理的含17Cr-12Ni-2.5Mo(最大含碳量为0.030)耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 7 页
SAE AMS 5654E-2001(R2006) 含18Cr-11Ni-0.60(Cb+Ta)自耗电极熔炼的、固溶热处理的耐腐蚀和耐热的航空优质钢棒、钢丝、锻件、钢管和环件(SAE 30347) 页
SAE AMS 5655E-2001 调质的含12.5Cr-0.75Ni-1.0Mo-1.0W-0.24V(0.20-0.25C)耐腐蚀和耐热的钢棒、钢丝和锻件 8 页
SAE AMS 5656D-2001(R2006) 固溶热处理的含9.0Mn-20Cr-6.5Ni-0.27N耐腐蚀的钢棒、钢丝、锻件、挤压件和环件 页
SAE AMS 5659L-2004 自耗电极熔炼的、固溶热处理的、脱溶淬硬的含15Cr-4.5Ni-0.30CB(Nb)-3.5Cu耐腐蚀的钢棒、钢丝、锻件、环件和挤压件 10 页
SAE AMS 5660J-2002 含12.5Cr-42.5Ni-6.0Mo-2.7Ti-0.015B-34Fe自耗电极或真空感应熔炼、稳定化处理、固溶热和脱溶热处理的耐腐蚀和耐热的镍-铁合金棒材和锻件 8 页
SAE AMS 5661F-2005 Nickel-Iron Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 42.5Ni - 12.5Cr - 5.8Mo - 2.9Ti - 0.015B - 35Fe Consumable Electrode or Vacuum Induction Melted Solution, Stabilization, and Precipitation Heat Treated Composition similar to UNS 页
SAE AMS 5662M-2004 1775°F(968°C)固溶热处理的、脱溶淬硬的、自耗电极或真空感应熔炼的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50Al-18Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 11 页
SAE AMS 5663M-2004 1775°F(968°C)固溶热和脱溶热处理的、自耗电极或真空感应熔炼的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50Al-18Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 11 页
SAE AMS 5664E-2001(R2006) 1950°F(1066°C)固溶热处理的、脱溶淬硬的、自耗电极或真空感应熔炼的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50Al-18Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 页
SAE AMS 5665M-2000 含74Ni-15.5Cr-8.0Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 8 页
SAE AMS 5666F-2006 Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, Extrusions, and Rings 62Ni - 21.5Cr - 9.0Mo - 3.65 (Cb+Ta) Annealed UNS N06625 页
SAE AMS 5667L-2003 均衡脱溶淬硬的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 8 页
SAE AMS 5668H-1993(R2000) 2100°F(1149°C)固溶热和脱溶热处理的含72Ni-15.5Cr-7.0Fe-2.5Ti-1.0(Cb+Ta)-0.70Al耐腐蚀和耐热的镍合金棒材、锻件和环件 9 页
SAE AMS 5670F-2005 Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb(Nb) - 2.5Ti - 0.70Al - 7.0Fe 1800 ? (982 ?) Solution Heat Treated, Precipitation-Hardenable Composition similar to UNS N07750 页
SAE AMS 5671G-2003 1800°F(982°C)固溶热处理的、脱溶淬硬的、自耗电极或真空感应熔炼的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 8 页
SAE AMS 5674E-2001 固溶热处理的含18Cr-11.5Ni-0.70Cb耐腐蚀和耐热的钢丝(SAE 30347) 5 页
SAE AMS 5675E-2001 含70Ni-2.4Mn-15.5Cr-3.0Ti-7.0Fe耐腐蚀和耐热的镍合金焊丝 6 页
SAE AMS 5676F-2006 Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 80Ni - 20Cr UNS N06003 页
SAE AMS 5678F-2002 冷拉制、脱溶淬硬的含17Cr-7.1Ni-1.1Al耐腐蚀钢丝 9 页
SAE AMS 5679G-2001(R2006) Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 73Ni - 15.5Cr - 2.2Cb - 8.0Fe UNS N06062 页
SAE AMS 5680J-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 18.5Cr - 11Ni - 0.40Cb (Nb) (SAE 30347) UNS S34781 页
SAE AMS 5682D-1993(R2000) 含78Ni-20Cr耐腐蚀和耐热的镍合金镀层杆材和线材 5 页
SAE AMS 5685K-2001 固溶热处理、冷加工的含18Cr-11.5Ni耐腐蚀的安全钢丝(SAE 30305) 6 页
SAE AMS 5686G-2001(R2006) 固溶热处理的含18Cr-11.5Ni耐腐蚀的铆接钢丝(SAE 30305) 页
SAE AMS 5687M-2002 退火的含74Ni-15.5Cr-8.0Fe耐腐蚀和耐热的镍合金丝 6 页
SAE AMS 5688K-2000 弹性回火的含18Cr-9.0Ni耐腐蚀钢丝(SAE 30302) 8 页
SAE AMS 5689F-2001 固溶热处理的含18Cr-10.5Ni-0.40Ti耐腐蚀和耐热的钢丝(SAE 30321) 5 页
SAE AMS 5690L-2001(R2006) Steel, Corrosion and Heat Resistant, Wire 17Cr - 12Ni - 2.5Mo (SAE 30316) Solution Heat Treated UNS S31600 页
SAE AMS 5692D-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 19Cr - 12.5Ni - 2.5Mo UNS S31680 页
SAE AMS 5694H-2001(R2006) 含27Cr-21.5Ni耐腐蚀和耐热的钢焊丝 页
SAE AMS 5696C-2002 19Cr-12.5Ni-2.5Mo铁素体含量高、耐腐蚀和耐热的钢焊丝 7 页
SAE AMS 5697F-2002 固溶热处理的含19Cr-9.5Ni耐腐蚀钢丝(SAE 30304) 5 页
SAE AMS 5698G-2003 No.1回火、脱溶淬硬的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金丝 7 页
SAE AMS 5699G-2003 弹性回火、脱溶淬硬的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金丝 8 页
SAE AMS 5700F-2006 Steel, Corrosion and Heat Resistant, Bars, Forgings, and Rings 13.5Cr - 13.5Ni - 0.35Mo - 2.2W Annealed 页
SAE AMS 5701C-1993(R2000) 1800°F(982°C)固溶热处理的、自耗电极或真空感应熔炼的含41.5Ni-16Cr-37Fe-2.9Cb-1.8Ti耐腐蚀和耐热的镍合金棒材、锻件和环件 9 页
SAE AMS 5702C-1993(R2000) 1750°F(954°C)固溶热处理的、自耗电极或真空感应熔炼的含41.5Ni-16Cr-37Fe-2.9Cb-1.8Ti耐腐蚀和耐热的镍合金棒材、锻件和环件 9 页
SAE AMS 5703C-1993(R2000) 1750°F(954°C)稳定化处理、固溶热和脱溶热处理、自耗电极或真空感应熔炼的含41.5Ni-16Cr-37Fe-2.9Cb-1.8Ti耐腐蚀和耐热的镍合金棒材、锻件和环件 10 页
SAE AMS 5703D-2006 Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 41.5Ni - 16Cr - 37Fe - 2.9Cb - 1.8Ti Consumable Electrode or Vacuum Induction Melted 1750 Degrees F (954 Degrees C) Solution, Stabilization, and Precipitation Heat Treated UNS N09706 页
SAE AMS 5704H-2006 Nickel Alloy, Corrosion and Heat Resistant, Forgings 57Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4Al - 0.05Zr - 0.006B Consumable Electrode or Vacuum Induction Melted 1825 to 1900 Degrees F (996 to 1038 Degrees C) Solution, Stabilization, and Precipitati 页
SAE AMS 5706K-2002 1825-1900°F固溶热处理的、自耗电极或真空感应熔炼的含57Ni-19.5Cr-13.5Co-4.3Mo-3.0Ti-1.4AI-0.006B-0.05Zr耐腐蚀和耐热的镍合金棒材、锻件和环件 8 页
SAE AMS 5707J-2000 1825-1900°F(996-1038°C)稳定化处理、固溶热和脱溶热处理的、自耗电极或真空感应熔炼的含58Ni-19.5Cr-13.5Co-4.3Mo-3.0Ti-1.4Al-0.05Zr-0.006B耐腐蚀和耐热的镍合金棒材、锻件和环件 9 页
SAE AMS 5708H-2002 1975°F(1079°C)固溶热处理的、自耗电极或真空感应熔炼的含58Ni-19.5Cr-13.5Co-4.3Mo-3.0Ti-1.4AI耐腐蚀和耐热的镍合金棒材、锻件和环件 7 页
SAE AMS 5708J-2006 Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 58Ni - 19.5Cr - 13.5Co - 4.3Mo - 3.0Ti - 1.4AI Consumable Electrode or Vacuum Induction Melted 1975 degrees F (1079 degrees C) Solution Heat Treated UNS N07001 页
SAE AMS 5709G-2000(R2006) 1975°F(1079°C)稳定化处理、固溶热和脱溶热处理的、自耗电极或真空感应熔炼的含58Ni-19.5Cr-13.5Co-4.3Mo-3.0Ti-1.4Al-0.05Zr-0.006B耐腐蚀和耐热的镍合金棒材和锻件 页
SAE AMS 5711D-2002 固溶热处理的含65Ni-15.8Cr-15.2Mo-0.30Al-0.05La耐腐蚀和耐热的镍合金棒材、锻件和环件 7 页
SAE AMS 5712H-2000 真空熔炼、固溶热处理、脱溶淬硬的含53Ni-19Cr-11Co-9.8Mo-3.2Ti-1.6Al-0.006B耐腐蚀和耐热的镍合金棒材、锻件和环件 10 页
SAE AMS 5712J-2006 Nickel Alloy, Corrosion and Heat Resistant, Bars, Forgings, and Rings 53Ni - 19Cr - 11Co - 9.8Mo - 3.2Ti - 1.6Al - 0.006B Vacuum Melted, Solution Heat Treated Precipitation Hardenable UNS N07041 页
SAE AMS 5713H-2000 真空熔炼、固溶热和脱溶热处理的含53Ni-19Cr-11Co-9.8Mo-3.2Ti-1.6Al-0.006B耐腐蚀和耐热的镍合金棒材、锻件和环件 10 页
SAE AMS 5714D-2006 Alloy Bars, Forgings, and Rings, Corrosion and Heat Resistant 73Ni - 15.5Cr - 2.5Ti - 0.70Al - 7.0Fe Precipitation Hardenable UNS N07722 页
SAE AMS 5715E-2004 退火的含60.5Ni-23Cr-14Fe-1.4Al耐腐蚀和耐热的镍合金棒材、锻件和环件 6 页
SAE AMS 5716H-2001(R2006) 固溶热处理的含44Fe-18.5Cr-35.5Ni-1.1Si耐热的铁-镍合金棒材、线材、锻件和环件 页
SAE AMS 5717H-2003 固溶热处理的含45.5Ni-25.5Cr-3.2Co-3.2Mo-3.2W-18.5Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 6 页
SAE AMS 5719C-2000 退火、真空电弧或电渣再熔炼的含11.8Cr-2.5Ni-1.8Mo-0.33V(0.08-0.15C)耐腐蚀的钢棒、钢丝、锻件、钢管、环件和挤压件 9 页
SAE AMS 5719D-2006 Steel Bars, Wire, Forgings, Tubing, Rings, and Extrusions, Corrosion Resistant 11.8 Cr - 2.5Ni - 1.8Mo - 0.33V (0.08 - 0.15C) Annealed, Vacuum Arc or Electroslag Remelted UNS S64152 页
SAE AMS 5726C-2001 1800°F(982°C)固溶热处理和加工硬化的、自耗电极熔炼的、抗拉强度为200ksi(1379MPa)含15Cr-25.5Ni-1.2Mo-2.1Ti-0.006B-0.30V耐腐蚀和耐热的钢棒和钢丝 6 页
SAE AMS 5726D-2006 Steel, Corrosion and Heat-Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V 1800 ? (982 ?) Solution Heat Treated and Work-Strengthened Consumable Electrode Melted 200 ksi (1379 MPa) Tensile Strength UNS S66286 页
SAE AMS 5731L-2006 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted, 1800 ? (982 ?) Solution Heat Treated UNS S66286 页
SAE AMS 5732H-2001 1800°F(982°C)固溶热和脱溶热处理的、自耗电极熔炼的含15Cr-25.5Ni-1.2Mo-2.1Ti-0.006B-0.30V耐腐蚀和耐热的钢棒、钢丝、锻件、钢管和环件 8 页
SAE AMS 5732J-2006 Steel, Corrosion and Heat Resistant, Bars, Wire, Forgings, Tubing, and Rings 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1800 Degrees F (982 Degrees C) Solution and Precipitation Heat Treated UNS S66286 页
SAE AMS 5734K-2006 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Tubing 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted, 1650 Degrees F (899 Degrees C) Solution Heat Treated UNS S66286 页
SAE AMS 5737P-2006 Steel, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Tubing 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1650 Degrees F (899 Degrees C) Solution and Precipitation Heat Treated UNS S66286 页
SAE AMS 5738D-2002 易切削、高屈服强度、固溶热处理和冷处理的含18Cr-9Ni耐腐蚀的钢棒和钢丝(SAE 30303F) 6 页
SAE AMS 5743J-2003 固溶热处理、零度以下冷却、均衡和过度回火的含15.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢棒和锻件 7 页
SAE AMS 5744E-2003 热处理的、抗拉强度为170ksi(1172MPa)含15.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢棒和锻件 6 页
SAE AMS 5745F-2003 均衡和过度回火的含16.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢棒和锻件 7 页
SAE AMS 5746F-2005 Alloy, Corrosion and Heat-Resistant, Bars and Forgings 15Cr - 45Ni - 4.1Mo - 4.1W - 3.0Ti - 1.0Al - 31Fe (D979) Consumable Electrode Vacuum Melted Solution and Precipitation Heat Treated Composition similar to UNS N09979 页
SAE AMS 5747C-2000 固溶热处理、脱溶淬硬的含72Ni-15.5Cr-0.95Cb-2.5Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 7 页
SAE AMS 5747D-2006 Nickel Alloy, Corrosion and Heat-Resistant, Bars, Forgings, and Rings 72Ni - 15.5Cr - 0.95Cb(Nb) - 2.5Ti - 0.70Al - 7.0Fe Solution Heat Treated, Precipitation Hardenable UNS N07750 页
SAE AMS 5749E-2003 优质轴承用两次真空熔炼的含14.5Cr-4.0Mo-1.2V(1.10-1.20C)耐腐蚀的钢棒、钢丝、锻件和钢管 9 页
SAE AMS 5754L-2002 固溶热处理的含47.5Ni-22Cr-1.5Co-9.0Mo-0.60W-18.5Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 7 页
SAE AMS 5755F-2002 固溶热处理的含64Ni-5.0Cr-24.5Mo-5.5Fe耐腐蚀和耐热的镍合金棒材、锻件和环件 6 页
SAE AMS 5758G-2002 真空感应加自耗电极真空熔炼、加工硬化用固溶热处理的含20Cr-35Ni-35Co-10Mo耐腐蚀合金棒 6 页
SAE AMS 5759K-2004 固溶热处理的含52Co-20Cr-10Ni-15W耐腐蚀和耐热的钴合金棒材、锻件和环件 7 页
SAE AMS 5762E-2001(R2006) 易切削、固溶热处理的含5.8Mn-17Cr-5.8Ni-2.0Cu-0.26S耐腐蚀的钢棒、钢丝和锻件 页
SAE AMS 5763C-2001(R2006) 固溶热处理的含15Cr-6.5Ni-0.75Mo-0.50(Cb+Ta)-1.5Cu耐腐蚀的钢棒、锻件、钢管和环件 页
SAE AMS 5764E-2003 固溶热处理的含5.0Mn-22Cr-12.5Ni-2.2Mo-0.20Cb-0.30N-0.20V耐腐蚀的钢棒、钢丝、锻件、挤压件和环件 7 页
SAE AMS 5766D-2003 固溶热处理的含21Cr-32.5Ni-0.38Ti-0.38Al-45Fe耐腐蚀和耐热的合金棒材和锻件 5 页
SAE AMS 5768K-2002 固溶热和脱溶热处理的含21Cr-20Ni-20Co-3.0Mo-2.5W-1.0Cb-0.15N-31Fe耐腐蚀和耐热的合金棒材、锻件和环件 7 页
SAE AMS 5769F-2003 固溶热处理的含21Cr-20Ni-20Co-3.0Mo-2.5W-1.0(Cb+Ta)-0.15N-32Fe耐腐蚀和耐热的合金棒材、锻件和环件 6 页
SAE AMS 5771E-2004 固溶热处理的含74Ni-7.0Cr-16.5Mo耐腐蚀和耐热的镍合金棒材、锻件和环件 6 页
SAE AMS 5772D-2004 固溶热处理的含40Co-22Cr-22Ni-14.5W-0.07La耐腐蚀和耐热的钴合金棒材、锻件和环件 8 页
SAE AMS 5773D-2000 自耗电极熔炼的、固溶热处理的、脱溶淬硬的含15Cr-6.5Ni-0.75Mo-0.30(Cb + Ta)-1.5Cu耐腐蚀的钢棒、钢丝、锻件、钢管和环件 11 页
SAE AMS 5774E-2002 含16.5Cr-4.5Ni-2.9Mo-0.10N耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5776E-2002 含12.5Cr耐腐蚀和耐热的钢焊丝(SAE 51410) 6 页
SAE AMS 5778E-2001 含72Ni-15.5Cr-1.0Cb-2.4Ti-0.70Al-7.0Fe耐腐蚀和耐热的镍合金焊丝 6 页
SAE AMS 5780E-2006 Steel, Corrosion and Heat Resistant, Welding Wire 15.5Cr - 4.5Ni - 2.9Mo - 0.10N UNS S35500 页
SAE AMS 5782F-2002 真空感应熔炼的含20.5Cr-9.0Ni-0.50Mo-1.5W-1.2Cb-0.20Ti耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5784E-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 29Cr - 9.5Ni UNS S64299 页
SAE AMS 5786E-2002 含62.5Ni-5.0Cr-24.5Mo-5.5Fe耐腐蚀和耐热的镍合金焊丝 6 页
SAE AMS 5788F-2006 Cobalt Alloy, Corrosion and Heat Resistant, Hard Facing Rods and Wire 62Co - 29Cr - 4.5W - 1.2C UNS R30006 页
SAE AMS 5789D-2003 含54Co-25.5Cr-10.5Ni-7.5W耐腐蚀和耐热的钴合金焊丝 6 页
SAE AMS 5790C-2003 20Cr-10Ni-0.75Cb铁素体含量高、耐腐蚀和耐热的钢焊丝 7 页
SAE AMS 5791B-2004 含56.5Co-25.5Cr-10.5Ni-7.5W的等离子喷涂钴合金粉 6 页
SAE AMS 5792A-1992(R1998) 50(88W-12Co)+35(70Ni-16.5Cr-4Fe-4Si-3.8B)+15(80Ni-20Al)三种成分混合物的等离子喷涂粉末 8 页
SAE AMS 5792B-2006 Powder, Plasma Spray 50 (88WC - 12Co) + 35 (70Ni - 16.5Cr - 4Fe - 4Si - 3.8B) + 15 (80Ni - 20A1) Three-Component Mixture 页
SAE AMS 5793A-1992(R1998) 含95Ni-5Al的等离子喷涂粉末 6 页
SAE AMS 5793B-2006 Powder, Plasma Spray 95Ni - 5Al 页
SAE AMS 5794E-2002 退火的含31Fe-21Cr-20Ni-20Co-3.0Mo-2.5W-1.0Cb-0.15N耐腐蚀和耐热的铁合金焊丝 6 页
SAE AMS 5796E-2006 Cobalt Alloy, Corrosion and Heat Resistant, Welding Wire 52Co - 20Cr - 10Ni - 15W UNS R30605 页
SAE AMS 5797D-2002 含51.5Co-20Cr-10Ni-15W耐腐蚀和耐热的钴合金药皮焊条 7 页
SAE AMS 5798E-2001 含47.5Ni-22Cr-1.5Co-9.0Mo-0.60W-18.5Fe耐腐蚀和耐热的镍合金焊丝 6 页
SAE AMS 5800F-2006 Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 54Ni - 19Cr - 11Co - 10Mo - 3.2Ti - 1.5Al - 0.006B Vacuum Induction Melted UNS N07041 页
SAE AMS 5801F-2006 Cobalt Alloy, Corrosion and Heat-Resistant, Welding Wire 39Co - 22Cr - 22Ni - 14.5W - 0.07La UNS R30188 页
SAE AMS 5802C-2006 Iron-Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 41Fe - 37.5Ni - 14Co - 4.8Cb (Nb) - 1.5Ti Vacuum Melted, Low Expansion UNS N19907 页
SAE AMS 5803D-2002 真空熔炼含16.4Cr-4.8Ni-0.22Cb-3.6Cu耐腐蚀和耐热的钢焊丝 7 页
SAE AMS 5804G-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 15Cr - 25.5Ni - 1.3Mo - 2.2Ti - 0.006B - 0.30V UNS S66286 and K66286 页
SAE AMS 5805G-2001 真空感应熔炼、环境受控包装的含15Cr-25.5Ni-1.2Mo-2.1Ti-0.004B-0.30V耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5808C-2006 Steel, Corrosion and Heat Resistant, Welding Wire 19Cr - 13Ni - 2.5Mo High Ferrite Grade, Trace Element Controlled 页
SAE AMS 5810A-2001(R2006) 1800°F(982°C)固溶处理、冷拉制或冷轧和老化的、自耗电极熔炼的含15Cr-25.5Ni-1.2Mo-2.1Ti-0.006B-0.30V耐腐蚀和耐热的扁钢丝 页
SAE AMS 5811C-2001 真空感应熔炼、环境受控包装的含15Cr-30Ni-1.2Mo-2.2Ti-0.25Al-0.001B-0.030V(0.01-0.03C)耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5812F-2001(R2006) 真空熔炼含15Cr-7.1Ni-2.4Mo-1.0Al耐腐蚀和耐热的钢焊丝 页
SAE AMS 5814C-2006 Cobalt Alloy, Corrosion and Heat-Resistant, Welding Wire 52Co - 20Cr - 20Ni - 7.5Ta Vacuum Melted UNS R30918 页
SAE AMS 5817F-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 13Cr - 2.0Ni - 3.0W UNS S41800 页
SAE AMS 5818A-2001 含9.0Mn-20Cr-6.2Ni-0.20N耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5819A-2001 含62Co-27Cr-2.9Ni-5.5Mo耐腐蚀和耐热的钴合金表面硬化杆材和线材 5 页
SAE AMS 5821G-2006 Steel, Corrosion-Resistant, Welding Wire 12Cr (SAE 51410 Modified) Ferrite Control Grade UNS S41081 页
SAE AMS 5822D-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 11.8Cr - 2.8Ni - 1.6Co - 1.8Mo - 0.32V Vacuum Induction Melted UNS S41780 页
SAE AMS 5823E-2001 含11.8Cr-2.8Ni-1.6Co-1.8Mo-0.32V耐腐蚀和耐热的钢焊丝 6 页
SAE AMS 5824E-2006 Steel, Corrosion-Resistant, Welding Wire 17Cr - 7.1Ni - 1.0Al UNS S17780 页
SAE AMS 5825G-2006 Steel, Corrosion-Resistant, Welding Wire 16.4Cr - 4.8Ni - 0.22Cb(Nb) - 3.6Cu UNS S17480 页
SAE AMS 5826D-2006 Steel, Corrosion and Heat-Resistant, Welding Wire 15Cr - 5.1Ni - 0.30Cb(Nb) - 3.2Cu UNS S15500 页
SAE AMS 5828G-2001 真空感应熔炼的、固溶热处理的含57Ni-19.5Cr-13.5Co-4.2Mo-3.1Ti-1.4Al-0.006B耐腐蚀和耐热的镍合金焊丝 6 页
SAE AMS 5829E-2006 Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 56Ni - 19.5Cr - 16.5Co - 2.5Ti - 1.5A1 Vacuum Induction Melted UNS N07090 页
SAE AMS 5830B-2001 含12.5Cr-42.5Ni-6.0Mo-2.7Ti-0.015B-35Fe耐腐蚀和耐热的镍-铁合金焊丝 6 页
SAE AMS 5831B-2001(R2006) 含29Fe-22Cr-21Ni-18.5Co-3.2Mo-2.8W-0.78Ta 0.30Al-0.05Zr-0.05La-0.20N耐腐蚀和耐热的合金焊丝 页
SAE AMS 5832F-2001(R2006) 自耗电极或真空感应熔炼的含52.5Ni-19Cr-3.0Mo-5.1Cb-0.90Ti-0.50Al-18Fe耐腐蚀和耐热的镍合金焊丝 页
SAE AMS 5833C-2003 固溶热处理和冷拉制的含20Cr-15Ni-40Co-7.0Mo-16Fe耐腐蚀和耐热的圆形钴合金丝 7 页
SAE AMS 5834C-2003 真空感应加自耗电极熔炼、固溶热处理、冷拉制和老化的含20Cr-15Ni-40Co-7.0Mo-16Fe耐腐蚀和耐热的圆形钴合金丝 7 页
SAE AMS 5835C-2001(R2006) 真空感应熔炼、环境受控包装的含72Ni-3.2Mn-20Cr-2.5Cb-0.48Ti耐腐蚀和耐热的镍合金焊丝 页
SAE AMS 5836B-2001(R2006) 含72Ni-3.0Mn-20Cr-2.5Cb耐腐蚀和耐热的镍合金焊丝 页
SAE AMS 5837F-1999 含62Ni-21.5Cr-9.0Mo-3.7Cb耐腐蚀和耐热的镍合金焊丝 7 页
SAE AMS 5837G-2006 Nickel Alloy, Corrosion and Heat Resistant, Welding Wire 62Ni - 21.5Cr - 9.0Mo - 3.7Cb(Nb) UNS N06625 页
SAE AMS 5838E-2006 Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 65Ni - 16Cr - 15Mo - 0.30Al - 0.06La UNS N06635 页
SAE AMS 5839A-2001(R2006) 含59Ni-22Cr-2.0Mo-14W-0.35Al耐腐蚀和耐热的镍合金焊丝 页
SAE AMS 5840D-2001(R2006) 真空熔炼的含13Cr-8.0Ni-2.3Mo-1.1Al耐腐蚀和耐热的钢焊丝 页
SAE AMS 5841D-2000 真空感应加真空自耗电极熔炼、加工硬化用固溶热处理的含19Cr-36Co-25Ni-7.0Mo-0.50Cb-2.9Ti-0.20Al-9.0Fe耐腐蚀和耐热的钴-镍合金棒材 8 页
SAE AMS 5841E-2006 Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated for Work Strengthening UNS R30159 页
SAE AMS 5842D-2000 真空感应加真空自耗电极熔炼、固溶热处理和加工硬化的含19Cr-36Co-25Ni-7.0Mo-0.50Cb-2.9Ti-0.20Al-9.0Fe耐腐蚀和耐热的钴-镍合金棒材 8 页
SAE AMS 5842E-2006 Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni -7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated and Work Strengthened USN R30159 页
SAE AMS 5843D-2000 真空感应加真空自耗电极熔炼、固溶热处理、加工硬化和老化的含19Cr-36Co-25Ni-7.0Mo-0.50Cb-2.9Ti-0.20Al-9.0Fe耐腐蚀和耐热的钴-镍合金棒材 8 页
SAE AMS 5843E-2006 Cobalt-Nickel Alloy, Corrosion and Heat Resistant, Bars 19Cr - 36Co - 25Ni - 7.0Mo - 0.50Cb - 2.9Ti - 0.20Al - 9.0Fe Vacuum Induction Plus Vacuum Consumable Electrode Melted Solution Heat Treated, Work Strengthened, and Aged UNS R30159 页
SAE AMS 5844F-2002 真空感应加自耗电极真空熔炼、固溶热处理和加工硬化的含20Cr-35Ni-35Co-10Mo耐腐蚀的合金圆棒 6 页
SAE AMS 5845G-2003 真空感应加自耗电极真空熔炼、固溶热处理、加工硬化和老化的含20Cr-35Ni-35Co-10Mo耐腐蚀的合金圆棒 6 页
SAE AMS 5846B-2005 Alloy, Corrosion and Heat-Resistant, Bars and Forgings 53Ni - 15Cr - 18.5Co - 5.0Mo - 3.2Ti - 4.2Al - 0.03B Double Vacuum Melted Solution, Stabilization, and Precipitation Heat Treated Composition similar to UNS N13020 页
SAE AMS 5848C-2004 固溶热处理的含8.0Mn-4.0Si-17Cr-8.5Ni-0.13N耐腐蚀和耐磨损的钢棒、钢丝、锻件、挤压件、钢管和环件 7 页
SAE AMS 5850C-1993(R2000) 方形网格、电阻焊、耐腐蚀和耐热的蜂窝夹心钢板 19 页
SAE AMS 5853C-2006 Steel, Corrosion and Heat Resistant, Bars and Wire 15Cr - 25.5Ni - 1.2Mo - 2.1Ti - 0.006B - 0.30V Consumable Electrode Melted 1800 Degrees F (982 Degrees C) Solution Treated and Work-Strengthened 160 ksi (1103 MPa) Tensile Strength UNS S66286 页
SAE AMS 5854A-2001(R2006) 固溶热处理的、自耗电极或真空感应熔炼的含61Ni-20.5Cr-8.5Mo-3.4Cb-1.3Ti-5.0Fe耐腐蚀和耐热的镍合金棒材、线材、锻件和环件 页
SAE AMS 5857A-2000 高屈服强度、固溶热处理和冷加工的含19Cr-10Ni耐腐蚀的钢棒和钢丝(SAE 30304) 6 页
SAE AMS 5858C-2001(R2006) 含15Cr-25.5Ni-1.2Mo-2.1Ti-0.006B-0.30V多次熔炼、1800°F(982°C)固溶热处理、脱溶淬硬的耐腐蚀和耐热焊接级薄钢板、钢带和钢板 页
SAE AMS 5859D-2001 自耗电极熔炼、固溶热处理、脱溶淬硬的含15Cr-6.5Ni-0.75Mo-0.30Cb-1.5Cu耐腐蚀的薄钢板、钢带和钢板 7 页
SAE AMS 5860F-2006 Steel, Corrosion Resistant, Sheet, Strip, and Plate 12Cr - 8.5Ni - 0.30Cb - 1.1Ti - 2.0Cu Multiple Melted, Solution Heat Treated, Precipitation Hardenable UNS S45500 页
SAE AMS 5862G-2005 Steel, Corrosion-Resistant, Sheet, Strip, and Plate 15Cr - 4.5Ni - 0.30Cb (Nb) - 3.5Cu Consumable Electrode Remelted, Solution Heat Treated Precipitation-Hardenable Composition similar to UNS S15500 页
SAE AMS 5863D-2001(R2006) 固溶热处理、脱溶淬硬的含15Cr-6.5Ni-0.75Mo-0.60Cb-1.5Cu耐腐蚀的薄钢板、钢带和钢板 页
SAE AMS 5864B-2003 真空感应加自耗电极熔炼、固溶热处理、脱溶淬硬的含13Cr-8.0Ni-2.2Mo-1.1Al耐腐蚀的钢板 8 页
SAE AMS 5865D-2001(R2006) 氧化钍分散增强耐腐蚀和耐热的薄镍板和镍带 页
SAE AMS 5866D-2006 Steel, Corrosion Resistant, Flat Wire 18Cr - 9.0Ni (SAE 30302) Spring Temper UNS S30200 页
SAE AMS 5867A-2001(R2006) 提高断裂韧度、退火的含12.5Cr耐腐蚀和耐热的钢锻件(SAE 51410) 页

 

标准获取办法：

在线提交	点击提交信息  （推荐）
电话联系	010-8334-5348
电子邮件	wwtrans@126.com

 

查看完整版本：SAE 标准数据库参考目录 3

© 标准规范中文版翻译

Powered by skycc.Archivers Author:圣捷